Motion Control Engineering 2000 User Manual

Index-1
Index
Numerics
2 BUS IS LOW 6-4
2 or 2xx Bus 6-3
2AB Spare input 5-30
2FS BUS IS LOW 6-4
2HA BUS IS LOW 6-4
2MV BUS IS LOW 6-4
702 - 7xx, Front Down Hall Call Indicator Outputs 5-40
702R - 7xxR, Rear Down Hall Call Indicator Outputs 5-40
801 - 8xx, Front Up Hall Call Indicator Outputs 5-40
801R - 8xxR, Rear Up Hall Call Indicator Outputs 5-40
900, Car Call Cancellation Output 5-40
A
ABD 6-44
ABD INPUT FAILURE message 6-4
ABI, Alarm Bell Input 5-30
absolute floor encoding 4-2
ABU 6-44
ABU INPUT FAILURE message 6-4
ABZ, Attendant Service Buzzer Output 5-40
ACCESS ENABLED message 6-4
ACI 5-30
ALI 5-30
ALLOW CAR CALLS ON WP SEC. option 5-49
ALT. PARKING FLOOR option 5-19
Alternate Lobby Input 5-30
ALV, Alive Input 5-30
ALV, Other car alive output flag 5-9
Analog Load Weigher Learn Function 5-64
ANALOG LOAD WEIGHER? option 5-52
API, Alternate Parking Input 5-30
API, Alternate Parking Input flag 5-9
ARST, Alarm Reset input 5-30
ASME A17.1 2000 Features Menu Options 5-54–5-55
ASME A17.1-2000 compliant 1-3
ASME A17.1A 2005 ADDENDA? option 5-21
ATD 6-44
ATD INPUT FAILURE message 6-4
ATS, Attendant Service Input 5-30
ATS. BYPASS SECURITY? option 5-53
Attendant Service Operation 1-15
Attendant Service Operation message 6-4
ATU 6-44
ATU INPUT FAILURE message 6-4
AUTO, Emergency power auto output flag 5-9
AUTO, Emergency Power Auto Selection Input 5-30
AUTOMATIC FLOOR STOP OPTION? option 5-50
Automatic Mode Fault Bypass 5-66
Auxiliary starter timeout message 6-5
AXR, Auxiliary Reset Input 5-30
B
BAB Spare input 5-30
BAB1 6-41
Basic Features Menu Options 5-17–5-19
Basic Security 5-60
programming or changing the Security codes 5-61
BATTERY BACKUP POWER SYSTEM FAULT 6-5
BATTERY POWER CAR RECALL ACTIVATED 6-5
Battery replacement 6-52
BFD, Bottom floor demand flag 5-9
BMS-LINK 1-21
Board Software Versions 5-107
Both USD and DSD are Open message 6-35
Bottom Access Distance, 65 5-104
BOTTOM ACCESS SW. FAILURE message 6-5
BOTTOM ACCESS? (F/R) option 5-54
Bottom Floor Demand message 6-5
Bottom floor level 5-104
BOTTOM FLOOR OR TOP FLOOR DEMAND message 5-12
Bottom Floor or Top Floor Demand message 6-5
Bottom Terminal Test 4-10
BOTTOM, Bottom landing output 5-40
BSI, Building Security Input 5-30
Bus Fuse Blown (2C) message 6-6
Bus Fuse Blown (2H) message 6-20
BYPASS STOP SW. ON PHASE 1 option 5-20
C
CAN Bus termination 6-62, 6-66
CANCEL BOTH HALL (U/D) CALLS option 5-50
CANCEL CAR CALLS BEHIND CAR? option 5-50
Capture For Test message 6-5
Car Call Bus is Disconnected message 6-6
CAR CALL CANCELS DOOR TIME option 5-22
CAR CALL DOOR TIMER 5-26
car calls, registering 4-3, 5-69
Car Controller
final adjustments 4-7, 4-8
ground wiring 2-8, 2-9
installation of 2-7
proper grounding 2-9
wiring 2-7
wiring prints 2-5
CAR DOOR BYPASS SW. FAILURE message 6-6
CAR IDENTIFIER option 5-19
Car in Test Mode message 6-6
CAR LANTERN DOOR FULLY OPEN option 5-28
Car Recall 1-18
Car Safety Device Open message 6-6
CAR SERVES FRNT/FLR X option 5-18
CAR SERVES REAR/FLR X? option 5-18
Car to Floor Function message 6-6
CAR TO FLOOR RETURN FLOOR option 5-53
Car to Lobby Operation message 6-6
CAR TOP INSPECTION ENABLE STUCK 6-6
CAR TOP INSPECTION message 6-6
card reader security 5-49
CARD REDR INPUTS - F CAR CALS? 5-49
CARD REDR INPUTS - F HAL CALS? 5-49
CARD REDR INPUTS - R CAR CALS? 5-49
CARD REDR INPUTS - R HAL CALS? 5-49

Motion Control Engineering 2000 Specifications

General

Brand	Motion Control Engineering
Model	2000
Category	Controller
Language	English