TABLE A
DISTANCE TRAVELED
1
(miles / km)
6 250 / 10 000
12 500 / 20 000
18 750 / 30 000
25 000 / 40 000
31 250 / 50 000
37 500 / 60 000
43 750 / 70 000
50 000 / 80 000
56 250 / 90 000
62 500 / 100 000
68 750 / 110 000
75 000 / 120 000
81 250 / 130 000
87 500 / 140 000
93 750 / 150 000
100 000 / 160 000
106 250 / 170 000
112 500 / 180 000
118 750 / 190 000
125 000 / 200 000
131 250 / 210 000
137 500 / 220 000
143 750 / 230 000
150 000 / 240 000
185 000 / 300 000
200 000 / 320 000
225 000 / 360 000
250 000 / 400 000
275 000 / 440 000
300 000 / 500 000
500 000 / 800 000
600 000 / 1 000 000
LUBRICATION AND
SERVICING SCHEDULE
Item
Months
proceed to maintenance operation at each
LUBRICANT /PART
2
05 COOLING
Coolant surge tank, test coolant solution
21 12
● ● ● ● ● ● ● ● ● ● ● ●
DDC S60 - Cooling system, drain, flush and refill
21 24
●
C
Volvo D13 - Coolant filter, change (Extended Life Coolant)
21 12
●
P13
Volvo D13 - Cooling system, drain, flush & refill (Extended Life
Coolant)
21 48
●
C
Replace crankshaft pulley’s rubber damper,
See Linnig Repair instruction 142.219 in Section 05
●
06 ELECTRICAL
Battery terminals, clean and coat terminals
30 12
120A HD 10 Bosch alternators, repair by replacement
T1 Bosh alternators, change brushes and voltage regulator
24
●
P22,P23
T1 Bosh alternators, change bearings
48
●
P24,P25
07 TRANSMISSION
5
llison transmission filled with non-TranSynd or non-TES 295 fluid
– Refer to TABLE 1 in Section 07: Transmission for fluid and filter
change
16
I, P16
Allison transmission filled with TranSynd or TES295 synthetic fluid
only, no mixture
6
, with Prognostics mode disabled – Refer to
TABLE 2 in Section 07: Transmission for fluid and filter change
16
H, P16
Allison transmission filled with TranSynd or TES295 synthetic fluid
only, no mixture with Prognostics mode enabled
6, 7
- Change
fluid & filters when indicated by TRANSMISSION SERVICE
indicator or 60 month (five years) whichever occurs first. In
addition, change filters with every fluid change.
16 60
H, P16
5
Allison Transmission recommends that customers use fluid analysis as the primary method for determining fluid change intervals. In the absence of a fluid analysis program, the fluid
change interval listed in the charts above and below should be used. Change filters according to the charts above and below even is a fluid analysis shows that the fluid doesn’t need
to be changed.
6
When the transmission contains a mixture of fluids (defined as the quantity of non-TranSynd/ non-TES 295 fluid remaining in the transmission after a fluid change combined with the
quantity of TranSynd™ required to fill the transmission to the proper level), perform the fluid and filter change according to the non-TranSynd™/non-TES 295 intervals.
7
Extended TranSynd™/TES 295 fluid and filter change intervals are only allowed with Allison High-Capacity filters. If using Gold Series filter, refer to TABLE 3 in Section 7 of this
manual for proper fluid and filter change intervals.
To Next Page
Loading...
Need help?
General
