Rohde & Schwarz SMAB-B92 - Page 491

Remote Control Commands
R&S
®
SMA100B
489User Manual 1178.3834.02 ─ 05
:TRACe<ch>[:POWer]:SWEep:MEASurement:POWer:LREFerence:DISPlay:
ANNotation[:STATe]..............................................................................................493
:TRACe<ch>[:POWer]:SWEep:MEASurement:POWer:MAXimum:DISPlay:ANNotation[:
STATe]................................................................................................................493
:TRACe<ch>[:POWer]:SWEep:MEASurement:POWer:MINimum:DISPlay:ANNotation[:
STATe]................................................................................................................493
:TRACe<ch>[:POWer]:SWEep:MEASurement:POWer:REFerence:DISPlay:ANNotation[:
STATe]................................................................................................................493
:TRACe<ch>[:POWer]:SWEep:MEASurement:POWer:PULSe:TOP:DISPlay:
ANNotation[:STATe]..............................................................................................493
:TRACe<ch>[:POWer]:SWEep:MEASurement:PULSe:SEParation:DISPlay:ANNotation[:
STATe]................................................................................................................493
:TRACe<ch>[:POWer]:SWEep:MEASurement:TRANsition:NEGative:DURation:DISPlay:
ANNotation[:STATe]..............................................................................................493
:TRACe<ch>[:POWer]:SWEep:MEASurement:TRANsition:NEGative:OCCurrence:
DISPlay:ANNotation[:STATe].................................................................................493
:TRACe<ch>[:POWer]:SWEep:MEASurement:TRANsition:NEGative:OVERshoot:
DISPlay:ANNotation[:STATe].................................................................................493
:TRACe<ch>[:POWer]:SWEep:MEASurement:TRANsition:POSitive:DURation:DISPlay:
ANNotation[:STATe]..............................................................................................493
:TRACe<ch>[:POWer]:SWEep:MEASurement:TRANsition:POSitive:OCCurrence:
DISPlay:ANNotation[:STATe].................................................................................493
:TRACe<ch>[:POWer]:SWEep:MEASurement:TRANsition:POSitive:OVERshoot:
DISPlay:ANNotation[:STATe].................................................................................493
:TRACe<ch>[:POWer]:SWEep:MEASurement:PULSe:ALL:DISPlay:ANNotation[:STATe].......494
:TRACe<ch>[:POWer]:SWEep:PULSe:THReshold:BASE?.................................................494
:TRACe<ch>[:POWer]:SWEep:PULSe:THReshold:POWer:HREFerence............................. 494
:TRACe<ch>[:POWer]:SWEep:PULSe:THReshold:POWer:LREFerence..............................495
:TRACe<ch>[:POWer]:SWEep:PULSe:THReshold:POWer:REFerence............................... 495
:TRACe<ch>[:POWer]:SWEep:STATe.............................................................................. 495
:TRACe[:POWer]:SWEep:MEASurement:FULLscreen:DISPlay:ANNotation[:STATe]............. 496
:TRACe[:POWer]:SWEep:MEASurement:GATE:DISPlay:ANNotation[:STATe]...................... 496
:TRACe[:POWer]:SWEep:MEASurement:MARKer:DISPlay:ANNotation[:STATe].................. 497
:TRACe[:POWer]:SWEep:MEASurement:PULSe:DISPlay:ANNotation[:STATe].................... 497
:TRACe[:POWer]:SWEep:MEASurement:STANdard:DISPlay:ANNotation[:STATe]................497
:TRACe<ch>[:POWer]:SWEep:COLor <Color>
Defines the color of a trace.
Parameters:
<Color> INVers | GRAY | YELLow | BLUE | GREen | RED | MAGenta
*RST: trace 1 = YELLow, trace 2 = GREen, trace 3 =
RED.
Example:
TRAC2:SWE:COL GRAY
Trace2 is indicated in gray color.
Manual operation: See " Color - Trace Power Analysis " on page 227
Power Sensor Measurement Subsystems