Schenck process Disomat Opus - Page 4

Contents
5 Setting Mode............................................................................................................41
5.1 Safety Through Password Protection.................................................................41
5.1.1 Default Passwords .......................................................................................42
5.1.2 Fct. 41:Password..........................................................................................42
5.1.3 Password Quick Input ..................................................................................43
5.1.4 Fct. 45:Change password ............................................................................43
5.2 Setting Using Parameter Password....................................................................44
5.2.1 Fct. 46:PRINT FORM...................................................................................46
5.2.1.1 Fct. 461:Form Texts ..............................................................................47
5.2.1.2 Fct. 462:Form Formats..........................................................................47
5.2.1.3 Fct. 463:Page Header Format...............................................................51
5.2.1.4 Fct. 464:String Name.............................................................................52
5.2.1.5 Fct. 465:EDP Format.............................................................................53
5.2.1.6 Fct. 466:Legal-For-Trade Memory Format............................................53
5.2.1.7 Fct. 467:Reset Consecutive Number ....................................................54
5.2.1.8 Fct. 468:Load Default Form...................................................................54
5.2.1.9 Fct. 469:Load Default Text ....................................................................57
5.2.2 Fct. 47:MATERIALS.....................................................................................58
5.2.2.1 Fct. 471:Max. Balance/Dumps ..............................................................58
5.2.2.2 Fct. 472:Clear balance ..........................................................................58
5.2.2.3 Fct. 473:Material data............................................................................58
5.2.3 Fct. 48:Fixed tare input ................................................................................59
5.2.4 Fct. 5c:Activate DISOPLAN Interfaces.........................................................59
5.3 Setting Using Configuration Password...............................................................60
5.3.1 Fct. 42:FUNCTION VARIANT......................................................................62
5.3.1.1 Fct. 421:Parameters..............................................................................62
5.3.1.2 Fct. 423:Load Variant ............................................................................62
5.3.2 Fct. 43:PERIPHERALS................................................................................62
5.3.2.1 Fct. 431:National Language Support.....................................................62
5.3.2.2 Fct. 432:Interfaces.................................................................................63
5.3.2.3 Fct. 433:COMMUNICATION .................................................................64
5.3.2.4 Fct. 4331:EDP .......................................................................................64
5.3.2.5 Fct. 4332:Printer....................................................................................65
5.3.2.6 Fct. 4333:Secondary Display.................................................................67
5.3.2.7 Fct. 4334:Fieldbus.................................................................................68
5.3.2.8 Fct. 434:Event Classes..........................................................................69
5.3.2.9 Fct. 435:Calibrate Analog Output..........................................................70
5.3.2.10 Fct. 436:IP Configuration.....................................................................72
5.4 Setting Using Calibration Password ...................................................................73
5.4.1 Fct. 44:SCALE..............................................................................................74
5.4.2 Fct. 441:Calibration Parameters ..................................................................75
5.4.2.1 Operating Sequence..............................................................................75
5.4.2.2 Parameter 'Unit'.....................................................................................76
5.4.2.3 Parameter 'Full Scale Value' .................................................................76
5.4.2.4 Parameter 'Increment Value'.................................................................76
5.4.2.5 Parameter 'No-Motion Difference' .........................................................76
5.4.2.6 Parameter 'Zero Setting Range'............................................................77
5.4.2.7 Parameter 'Overrange' ..........................................................................77
5.4.2.8 Parameter 'Mechanical Factor'..............................................................77
5.4.2.9 Parameter 'Calibration Factor'...............................................................78
5.4.2.10 Parameter 'Load Cell Rated Capacity' ................................................79
5.4.2.11 Parameter 'Number of Load Cells'.......................................................79
5.4.2.12 Parameter 'Load Cell Characteristic'...................................................79
5.4.2.13 Parameter 'Dead Weight'.....................................................................79
5.4.2.14 Parameter 'Legal-For-Trade' ...............................................................80
5.4.2.15 Parameter 'Scale ID'............................................................................80
5.4.2.16 Parameter 'Class' ................................................................................80
5.4.2.17 Parameter 'Gravity Deviation'..............................................................80
5.4.2.18 Parameter 'User Def. MIN Load'..........................................................80
BV-H2313 GB 0630 DISOMAT
®
Opus – Operating Manual
- II - © Schenck Process GmbH, Darmstadt