EasyManuals Logo

Siemens SINUMERIK 828D Function Manual

Siemens SINUMERIK 828D
1799 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #25 background imageLoading...
Page #25 background image
Basic Functions
Function Manual, 09/2011, 6FC5397-0BP40-2BA0
25
Table of contents
14.4.1.2 Preconditions of the status update ........................................................................................ 1132
14.4.1.3 Influence of the operating state on the target system ............................................................ 1132
14.4.1.4 Communication and cycle ..................................................................................................... 1132
14.4.1.5 Status update ........................................................................................................................ 1133
14.4.1.6 Simulating process conditions ............................................................................................... 1133
14.4.1.7 Checking cross references and the elements used ............................................................... 1133
14.4.2 Program status in the LAD program editor ............................................................................ 1134
14.4.2.1 Display program status .......................................................................................................... 1134
14.4.2.2 Display properties .................................................................................................................. 1136
14.4.2.3 Restrictions ............................................................................................................................ 1137
14.4.2.4 Adapting the program status display ..................................................................................... 1137
14.4.3 Displaying the status in a status chart ................................................................................... 1138
14.4.3.1 Properties of a status chart .................................................................................................... 1138
14.4.3.2 Open status chart .................................................................................................................. 1140
14.4.3.3 Working with several status charts ........................................................................................ 1140
14.4.3.4 Creating a status chart .......................................................................................................... 1141
14.4.3.5 Editing the status chart .......................................................................................................... 1142
14.4.3.6 Data formats .......................................................................................................................... 1143
14.4.3.7 Enabling the status table ....................................................................................................... 1144
14.4.3.8 Working with test functions in the status chart ...................................................................... 1145
14.4.4 Execute cycles ....................................................................................................................... 1145
14.5 Data interface ........................................................................................................................ 1147
14.5.1 PLC-NCK interface ................................................................................................................ 1147
14.5.1.1 Mode signals ......................................................................................................................... 1147
14.5.1.2 NC channel signals ................................................................................................................ 1148
14.5.1.3 Axis and spindle signals ........................................................................................................ 1149
14.5.1.4 General NCK signals ............................................................................................................. 1150
14.5.1.5 Fast data exchange PLC-NCK .............................................................................................. 1151
14.5.2 PLC-HMI interface ................................................................................................................. 1152
14.6 Function interface .................................................................................................................. 1153
14.6.1 Read/write NC variables ........................................................................................................ 1153
14.6.1.1 User interface ........................................................................................................................ 1153
14.6.1.2 Operable variables ................................................................................................................ 1157
14.6.2 Program instance services (PI services) ..................
............................................................. 1163
14.6.2.1 User interface ........................................................................................................................ 1163
14.6.2.2 PI services ............................................................................................................................. 1166
14.6.3 PLC user alarms .................................................................................................................... 1168
14.6.3.1 User interface ........................................................................................................................ 1168
14.6.4 PLC axis control .................................................................................................................... 1171
14.6.4.1 Overview ................................................................................................................................ 1171
14.6.4.2 User interface ........................................................................................................................ 1172
14.6.4.3 Spindle positioning ................................................................................................................ 1175
14.6.4.4 Rotate spindle ........................................................................................................................ 1176
14.6.4.5 Oscillate spindle .................................................................................................................... 1178
14.6.4.6 Indexing axis .......................................................................................................................... 1180
14.6.4.7 Positioning axis metric ........................................................................................................... 1182
14.6.4.8 Positioning axis inch .............................................................................................................. 1184
14.6.4.9 Positioning axis metric with handwheel override ................................................................... 1185
14.6.4.10Positioning axis inch with handwheel override ...................................................................... 1187
14.6.4.11Rotate spindle with automatic gear stage selection .............................................................. 1189
14.6.4.12Rotate spindle with constant cutting rate [m/min] .................................................................. 1190

Table of Contents

Other manuals for Siemens SINUMERIK 828D

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Siemens SINUMERIK 828D and is the answer not in the manual?

Siemens SINUMERIK 828D Specifications

General IconGeneral
Control TypeCNC
Operating SystemWindows Embedded
ProcessorIntel Atom
Display10.4" color TFT display
InterfacesEthernet, USB
ProgrammingShopMill, ShopTurn
Operation Panel Size10.4"
Protection ClassIP65
PLC Memory2 MB
Spindle Capacity4 spindles
Hard DriveCompactFlash

Related product manuals