Siemens SINUMERIK 828D Function Manual

Table of contents
Basic Functions
32 Function Manual, 09/2011, 6FC5397-0BP40-2BA0
19.1.6 Signals to channel (DB21, ...) ................................................................................................ 1623
19.1.7 Signals from channel (DB21, ...) ............................................................................................ 1624
19.1.8 Signals to axis/spindle (DB31, ...) .......................................................................................... 1625
19.1.9 Signals from axis/spindle (DB31, ...) ...................................................................................... 1637
19.2 Axis monitoring, protection zones (A3) .................................................................................. 1652
19.2.1 Signals to channel (DB21, ...) ................................................................................................ 1652
19.2.2 Signals from channel (DB21, ...) ............................................................................................ 1653
19.2.3 Signals to axis/spindle (DB31, ...) .......................................................................................... 1654
19.2.4 Signals from axis/spindle (DB31, ...) ...................................................................................... 1656
19.3 Continuouspath mode, exact stop and LookAhead (B1)...................................................... 1657
19.3.1 Signals from channel (DB21, ...) ............................................................................................ 1657
19.3.2 Signals from axis/spindle (DB31, ...) ...................................................................................... 1657
19.4 Travel to fixed stop (F1)......................................................................................................... 1659
19.4.1 Signals to axis/spindle (DB31, ...) .......................................................................................... 1659
19.4.2 Signals from axis/spindle (DB31, ...) ...................................................................................... 1660
19.5 Help function output to PLC (H2)........................................................................................... 1662
19.5.1 Signals to channel (DB21, ...) ................................................................................................ 1662
19.5.2 Signals from channel (DB21, ...) ............................................................................................ 1662
19.5.3 Signals from axis/spindle (DB31, ...) ...................................................................................... 1666
19.6 Mode group, channel, program operation, reset response (K1)............................................ 1667
19.6.1 Signals to mode group (DB11) .............................................................................................. 1667
19.6.2 Signals from the mode group (DB11) .................................................................................... 1671
19.6.3 Signals to channel (DB21, ...) ................................................................................................ 1675
19.6.4 Signals from channel (DB21, ...) ............................................................................................ 1679
19.6.5 Signals to axis/spindle (DB31, ...) .......................................................................................... 1692
19.6.6 Signals from axis/spindle (DB31, ...) ...................................................................................... 1692
19.7 Axis types, coordinate systems, frames (K2)......................................................................... 1695
19.7.1 Signals to axis/spindle (DB31, ...) .......................................................................................... 1695
19.8 Emergency Stop (N2) ............................................................................................................ 1696
19.8.1 Signals to NC (DB10) ............................................................................................................ 1696
19.8.2 Signals from NC (DB10) ........................................................................................................ 1697
19.9 PLC basic program (P3) ........................................................................................................ 1697
19.10 Reference point approach (R1) ............................................................................................. 1698
19.10.1 Signals to channel (DB21, ...) ...........................
..................................................................... 1698
19.10.2 Signals from channel (DB21, ...) ............................................................................................ 1699
19.10.3 Signals to axis/spindle (DB31, ...) .......................................................................................... 1699
19.10.4 Signals from axis/spindle (DB31, ...) ...................................................................................... 1700
19.11 Spindles (S1) ......................................................................................................................... 1702
19.11.1 Signals to axis/spindle (DB31, ...) .......................................................................................... 1702
19.11.2 Signals from axis/spindle (DB31, ...) ...................................................................................... 1708
19.12 Feeds (V1)............................................................................................................................. 1718
19.12.1 Signals to channel (DB21, ...) ................................................................................................ 1718
19.12.2 Signals to axis/spindle (DB31, ...) .......................................................................................... 1727
19.12.3 Signals from axis/spindle (DB31, ...) ...................................................................................... 1733
19.12.4 Signals from axis/spindle (DB31, ...) ...................................................................................... 1742

Siemens SINUMERIK 828D Specifications

General

Control Type	CNC
Operating System	Windows Embedded
Processor	Intel Atom
Display	10.4" color TFT display
Interfaces	Ethernet, USB
Programming	ShopMill, ShopTurn
Operation Panel Size	10.4"
Protection Class	IP65
PLC Memory	2 MB
Spindle Capacity	4 spindles
Hard Drive	CompactFlash