SMC Networks HRL100-A 40 Series User Manual

HRX-OM-X037
Chapter 7 Alarm Notifications and Troubleshooting
HRL Series 7.3 Troubleshooting
7-3
Table 7.3-1 Alarm codes and troubleshooting (1/2)
Sub code Operation Threshold
AL01
FLT
－
AL02 WRN －
AL03 FLT －
AL04 WRN －
AL06 5 FLT
－
Check that there is no abnormality
with the power supply system
(e.g. ground fault, short-circuit, voltage
fluctuation,abnormal interphase voltage,
open phase, surge).
AL07 6 WRN －
Air exhaust fan failure. Ask for service for the air exhaust
fan.
AL09 FLT 55ºC
AL10 OFF 1 45ºC 3
AL13 FLT 50ºC
AL14 OFF 1 45ºC 3
AL20 FLT 1 0.03MPa 3 Restart the thermo-chiller and check if the pump runs.
AL22 FLT 0.50MPa
AL23 FLT 1 0.50MPa 3
AL24 FLT 1 0.03MPa 3
AL25 FLT 0.03MPa
AL27 WRN 2 45.0μS/cm 3 Replace CH2 DI filter.
AL28 4 WRN 2 45.0μS/cm 3 Replace CH1 DI filter.
AL30 FLT 1
－
AL31 FLT 1
－
AL33 FLT
Less than 2.0LPM
-T2：Less than 5.0LPM
-T3：Less than 10.0LPM
Display flow rate : Threshold or less.
Check the piping is thin, closing of external valve, collapse
of piping, clogging of filter.
AL35
Ambient Temp.
OFF 2
2ºC/45ºC
Check the environment.
Digital input 1
Contact input has been detected.
Digital input 2
AL34
Communication
WRN 1
－
No request message from the host computer.
Try to send the request message again.
AL26
CH2 Flow Sensor
FLT 1
－
Short-circuit or broken wire of the flow rate sensor.
Ask for the service.
CH2 High Electric conductivity
CH1 High Electric conductivity
CH2 Low Flow FLT
CH2 High Press. Error
Check that there is no bending, collapse,
or clogging with the external piping.
Check that there is no clogging of the particle filter.
CH2 High Press.
CH2 Low Press.
Restart the thermo-chiller and check if the pump runs.
(Check the flow rate display value.)
CH2 Low Press. Error
CH1 Low Press.
AL21
CH2 Press. Sensor
FLT 1
－
Short-circuit or broken wire of the pressure sensor.
Ask for the service.
AL18
CH1 Press. Sensor
FLT 1
－
Short-circuit or broken wire of the pressure
sensor.Ask for the service.
AL19
CH1 High Press.
FLT 1
0.50MPa 3
Check that there is no bending, collapse,
or clogging with the external piping.
Check that there is no clogging of the particle filter.
AL16
CH2 TEMP READY ALARM
OFF 1
+1/-1ºC 3
・There may be causes such as large load
fluctuation and flow rate fluctuation.
・Please review the setting value.
AL17
CH1 HX In High Temp. FLT
FLT
60ºC
・Check that the circulating fluid flow rate
is more than the minimum flow rate.
・Check that the heat load is within
the specified range.
CH2 High Temp. FLT
・Check that the ambient temperature,
and heat load satisfy the specifications,
and that the circulating fluid flow rate is more
than the minimum flow rate.
・Please review the setting value.
CH2 High Temp.
AL15
CH2 Low Temp.
OFF 1
5ºC 3
・Check the effect of ambient temperature.
・Please review the setting value.
AL11
CH1 Low Temp.
OFF 1
5ºC 3
・Check the effect of ambient temperature.
・Please review the setting value.
AL12
CH1 TEMP READY ALARM
OFF 1
+1/-1ºC 3
・There may be causes such as large
load fluctuation and flow rate fluctuation.
・Please review the setting value.
CH2 Low Level FLT
The circulating fluid level of CH2 has decreased.
Refilling circulating fluid.
CH2 Low Level WRN
Fan Inverter
CH1 Hgih Temp. FLT
・Check that the ambient temperature,
and heat load satisfy the specifications,
and that the circulating fluid flow rate is
more than the minimum flow rate.
・Please review the setting value.
CH1 Hgih Temp.
Alarm
code
Alarm content
Default setting
Cause/Countermeasure
(Please reset the alarm after eliminating the cause.)
CH1 Low Level FLT
The circulating fluid level of CH1 has decreased.
Refilling circulating fluid.
CH1 Low Level WRN
Internal Cooling Fan

SMC Networks HRL100-A 40 Series Specifications

General

Brand	SMC Networks
Model	HRL100-A 40 Series
Category	Chiller
Language	English