TRENDnet TPE-3012LS

To Next Page

To Previous Page

TRENDnet User’s Guide

TPE-3012LS / TPE-3018LS

4. Click Apply.

5. In the top right, click Save to save the configuration settings to NV-RAM/startup

configuration.

6. Click OK.

Main Page

Table of Contents2
Product Overview5
Package Contents5
Features6
Product Hardware Features7
Application Diagram10
Switch Installation11
Desktop Hardware Installation11
Rack Mount Hardware Installation11
Basic Installation12
Connect Additional Devices to Your Switch14
Access Your Switch Management Page15
Saving Configuration and Switch between Web Modes15
Saving Configuration Changes to NV-RAM15
Switching between Standard and Surveillance Mode Web Interfaces16
Surveillance Mode Web Interface17
Dashboard17
Status17
Overview18
Port Info19
IP Camera Info19
NVR Info20
Poe Info20
Poe Scheduling21
Time23
Clock Settings23
SNTP Settings23
IP Settings25
SNMP Host Settings25
Surveillance Settings25
Log Server26
Password Settings27
Mail Alert27
PD Alive Check28
Onvif29
Discovering and Authorizing ONVIF Compliant Devices29
Applying IP Address Settings to ONVIF Authorized Devices30
Changing the ONVIF Device Administrator Password32
Creating New ONVIF Users in the ONVIF Device33
Upgrade ONVIF Device Firmware34
E-Map Management35
Tools37
View Firmware Information37
Firmware Upgrade and Backup37
Backup/Restore Switch Configuration39
Reset Switch to Factory Default40
Reboot Switch40
Standard Mode Web Interface41
Status41
View Your Switch System Information41
System Information41
View Your Switch Logging Messages42
View Your Switch Port Status Information43
View Link Aggregation Status45
View the MAC Address Table45
Network46
Set Your Ipv4 Settings46
Set Your Ipv6 Settings47
Set the Switch Date and Time49
Set the Web Management Idle Timeout50
Port51
Configure Your Switch Ports and View Port Status51
Enable Long-Range Poe Mode on Poe Ports52
Configure Error Disabled Port State53
Configure Trunk/Link Aggregation Settings54
Configure Port Power Savings56
Enable Jumbo Frame Support57
Onvif58
Discovering and Authorizing ONVIF Compliant Devices58
Applying IP Address Settings to ONVIF Authorized Devices59
Changing the ONVIF Device Administrator Password60
Creating New ONVIF Users in the ONVIF Device61
Upgrade ONVIF Device Firmware62
Poe (Power over Ethernet)63
Enable or Disable Poe63
Poe Scheduling64
PD Alive Check65
Vlan66
Add, Modify, and Remove Vlans66
Modify VLAN Port Membership68
Modify VLAN Port Settings69
Voice VLAN70
Create a Voice VLAN71
Configure Voice VLAN OUI Settings73
Mac Vlan74
Create MAC-Based VLAN Groups74
Configure MAC VLAN Group Binding75
Surveillance VLAN76
Create a Surveillance VLAN77
Configure Surveillance VLAN OUI Settings78
MAC Address Table79
View the Switch MAC Address Table79
Add Static MAC Address Entries79
Add MAC Addresses Used in Filtering80
Spanning Tree (STP, RSTP, MSTP)81
Configure Spanning Tree Protocol Settings81
Configure Spanning Tree Protocol Port Settings83
Configure Spanning Tree Protocol MST Settings (MSTP)84
Configure Spanning Tree Protocol MST Port Settings (MSTP)86
View Your Spanning Tree Protocol Instance Statistics Information (MSTP)87
LLDP (Link-Layer Discovery Protocol)87
Configure LLDP Settings87
Configure LLDP Port Settings88
View LLDP Packet View Detail89
View LLDP Local Information90
View LLDP Neighbors91
View LLDP Statistics Counters91
View LLDP Neighbor Information93
Multicast94
Configure Unknown Multicast and Multicast Forwarding Method94
Add Static Multicast Group Addresses95
Add Multicast Router Ports96
Configure IGMP Snooping Settings97
Configure IGMP Snooping Settings for Ipv4 Multicast Traffic97
Configure Multicast Querier Settings99
View IGMP Snooping Statistics100
Configure MLD Snooping Settings101
Configure MLD Snooping Settings for Ipv6 Multicast Traffic101
View MLD Snooping Statistics103
Configure MVR Settings104
Configure MVR Port Settings105
Configure MVR Group Address Table106
Security107
Configure RADIUS Settings107
Configure RADIUS Network Authentication Settings109
Configure RADIUS Network Port Settings111
View Authenticated Sessions113
Configure Management Access114
Configure Management ACL/ACE (Access Control Lists/Access Control Entries)116
Create New Access Control List116
Configure Port Security118
Configure Protected Ports119
Configure Storm Control120
Denial of Service (Dos)121
DHCP Snooping123
View DHCP Snooping Statistics124
Configure DHCP Option 82 Settings125
Configure DHCP Option 82 Circuit ID Settings127
Configure IP Source Guard128
Configure IP Source Guard IMPV Binding129
Save DHCP Snooping Database130
Acl131
Configure MAC ACL131
Configure MAC ACE132
Configure Ipv4 ACL134
Configure Ipv4 ACE135
Configure ACL Port Binding138
Qos140
Configure Qos Global Settings140
Configure Queue Scheduling141
Configure Cos Mapping142
Configure IP Precedence Mapping143
Configure Rate Limiting Per Port144
Diagnostics146
Configure Logging146
Configure Remote Logging/Syslog Server147
Configure Port Mirroring148
Ping Test149
Ping Watchdog150
Traceroute151
Copper Test151
Fiber Module152
Udld153
View UDLD Neighbors155
Modify Admin Password and Create New Users156
Management156
Upgrade Switch Firmware157
Backup/Restore Switch Configuration158
Save Switch Configuration to NV-RAM / Restore to Default160
Snmp161
Configure the SNMP View Table161
Configure the SNMP Group Table162
Configure the SNMP Community Table163
Configure the SNMP Users164
Set the SNMP Engine ID166
Configure the SNMP Trap Management167
Configure the SNMP Notification168
Rmon169
View RMON Statstics169
Configure RMON History Table171
Configure RMON Event Table172
Configure RMON Alarm Table173
Create Schedules175
Technical Specifications176
Troubleshooting181
Appendix182

TRENDnet TPE-3012LS - Page 48

Table of Contents

Related product manuals