To Next Page

To Previous Page

24-1

IM PX8000-02EN

24.1 Calibrating the PX8000

This section explains how to calibrate the PX8000. Execute calibration when you want to make

accurate measurements.

► Features Guide: “Calibration (Zero-level compensation, CAL)”

CAL Menu

Press SHIFT+DISPLAY MODE (CAL) to display the following menu.

Set the calibration that is performed after starting signal acquisition on AUX

modules (OFF, AUTO).

This command does not appear if AUX modules are not installed.

Turns on and off the calibration that is performed when a measurement is

completed on an element

Executes calibration

Chapter 24 Other Operations

Default Chapter4
- Conventions Used in this Manual4
- Key and Jog Shuttle Operations5
- Entering Values and Strings8
- Table of Contents10
Chapter 1 Fundamental Measurement Conditions14
- Configuring Wiring System Settings14
- Configuring Power Measurement Element Settings16
- Setting the Motor Mode17
Chapter 2 Vertical and Horizontal Control18
- Configuring Voltage Measurements18
- Configuring Current Measurements21
- Configuring Power Measurements25
- Configuring Sensor Input Voltage Measurements27
- Configuring Rotating Speed Measurements34
- Configuring Torque Measurements40
- Displaying the Menu for Configuring All Channels46
- Configuring the Horizontal Axis (Time Axis)48
Chapter 3 Triggering49
- Setting the Trigger Mode49
- Setting the Trigger Position and Trigger Delay50
- Setting the Trigger Hold off51
- Triggering on an Edge Trigger (Simple)52
- Triggering on a Timer Trigger (Simple)53
- Triggering on an External Trigger (Simple)54
- Triggering on a Power Line Signal (Simple)55
- Enhanced Trigger56
Chapter 4 Waveform Acquisition67
- Setting Conditions for Waveform Acquisition67
- Starting and Stopping Waveform Acquisition69
Chapter 5 Display Mode70
- Selecting the Display Mode70
Chapter 6 Numeric Data Display71
- Switching the Displayed Page71
- Changing the Displayed Items on the 4-, 8-, and 16-Value Displays73
- Changing the Displayed Items on the Matrix Display75
- Changing the All Items Display77
- Changing the Harmonics List Display (Option)78
- Setting the Custom Display80
Chapter 7 Numeric Computation83
- Turning Numeric Measurement on and off83
- Setting the Calculation Period84
- Setting Numeric Data Averaging85
- Setting User-Defined Functions86
- Setting Apparent Power, Reactive Power, and Corrected Power Equations88
- Setting the Phase Difference Display Format90
- Setting Harmonic Measurement Conditions91
Chapter 8 Waveform Display92
- Setting the Waveform Display92
- Using the Snapshot and Clear Trace Features94
Chapter 9 Bar Graph Display (Option)95
- Configuring the Bar Graph Display95
Chapter 10 Vector Display (Option)96
- Configuring the Vector Display96
Chapter 11 X-Y Display97
- Displaying X-Y Waveforms97
Chapter 12 Zooming Waveforms99
- Zooming in on or out of Waveforms99
Chapter 13 Cursor Measurement103
- Measuring with Horizontal Cursors103
- Measuring with Vertical Cursors104
- Measuring with Marker Cursors (Marker)105
- Measuring with Angle Cursors (Degree)107
- Measuring with Horizontal and Vertical Cursors (H & V)108
- Measuring with Peak Cursors (Peak)109
Chapter 14 Automated Measurement of Waveform Parameters110
- Automatically Measuring Waveform Parameters110
- Performing Normal Statistical Processing113
- Performing Cyclic Statistical Processing114
Chapter 15 Waveform Computation116
- Performing Addition, Subtraction, Multiplication, and Division116
- Performing Binary Conversion117
- Shifting the Phase118
- Displaying the Power Spectrum119
- Performing User-Defined Computations120
Chapter 16 FFT120
- Displaying FFT Waveforms123
Chapter 17 GO/NO-GO Determination125
- Performing GO/NO-GO Determination with Waveform Zones125
- Performing GO/NO-GO Determination with Waveform Parameters128
Chapter 18 Action128
- Setting Actions130
Chapter 19 Searching Waveforms132
- Searching for Edges132
- Searching for a Specific Time134
Chapter 20 Displaying and Searching History Waveforms135
- Displaying Waveform History Waveforms135
- Searching History Waveforms137
Chapter 21 Printing and Saving Screen Captures140
- Loading Roll Paper into the Built-In Printer (Optional)140
- Printing on the Built-In Printer (Option)142
- Saving Screen Captures to Files143
Chapter 22 Saving and Loading Data145
- Connecting Storage Media145
- Formatting Storage Media148
- Saving Waveform Data150
- Saving Numeric Data155
- Saving Setup Data158
- Saving Other Types of Data159
- Loading Waveform Data163
- Loading Setup Data164
- Loading Other Types of Data165
- Performing File Operations166
- Display Format167
Chapter 23 Ethernet Communication173
- Connecting the PX8000 to a Network173
- Connection Procedure174
- Configuring TCP/IP Settings175
- Accessing the PX8000 from a PC (FTP Server)176
- Connecting to a Network Drive177
- Using SNTP to Set the Date and Time178
Chapter 24 Other Operations179
- Calibrating the PX8000179
- Using the NULL Feature180
- Setting Time Synchronization (Option)181
- Changing the Message, Menu, and USB Keyboard Languages182
- Adjusting the Backlight183
- Initializing the Settings184
- Configuring the Environment Settings185
- Storing and Recalling Setup Data187
- Locking the Keys188

Brand	YOKOGAWA
Model	PX8000
Category	Measuring Instruments
Language	English

YOKOGAWA PX8000 User Manual

Table of Contents

Questions and Answers:

YOKOGAWA PX8000 Specifications

Related product manuals