To Next Page

To Previous Page

17-4

IM PX8000-02EN

17.2 Performing GO/NO-GO Determination with

Waveform Parameters

This section explains the following settings for performing GO/NO-GO determination with waveform

parameters.

• GO/NO-GO determination mode

• Judgment condition

• Action

• Determination period

► Features Guide: “Waveform Parameters (Parameter)”

“Automated Measurement of Waveform Parameters”

GO/NO-GO Menu

Press SHIFT+MEASURE (GO/NO-GO) to display the following menu.

Set the judgment conditions.

Set the actions. ► section 17.1

Set the determination period. ► section 17.1

Set the GO/NO-GO determination mode to Parameter.

Default Chapter4
- Conventions Used in this Manual4
- Key and Jog Shuttle Operations5
- Entering Values and Strings8
- Table of Contents10
Chapter 1 Fundamental Measurement Conditions14
- Configuring Wiring System Settings14
- Configuring Power Measurement Element Settings16
- Setting the Motor Mode17
Chapter 2 Vertical and Horizontal Control18
- Configuring Voltage Measurements18
- Configuring Current Measurements21
- Configuring Power Measurements25
- Configuring Sensor Input Voltage Measurements27
- Configuring Rotating Speed Measurements34
- Configuring Torque Measurements40
- Displaying the Menu for Configuring All Channels46
- Configuring the Horizontal Axis (Time Axis)48
Chapter 3 Triggering49
- Setting the Trigger Mode49
- Setting the Trigger Position and Trigger Delay50
- Setting the Trigger Hold off51
- Triggering on an Edge Trigger (Simple)52
- Triggering on a Timer Trigger (Simple)53
- Triggering on an External Trigger (Simple)54
- Triggering on a Power Line Signal (Simple)55
- Enhanced Trigger56
Chapter 4 Waveform Acquisition67
- Setting Conditions for Waveform Acquisition67
- Starting and Stopping Waveform Acquisition69
Chapter 5 Display Mode70
- Selecting the Display Mode70
Chapter 6 Numeric Data Display71
- Switching the Displayed Page71
- Changing the Displayed Items on the 4-, 8-, and 16-Value Displays73
- Changing the Displayed Items on the Matrix Display75
- Changing the All Items Display77
- Changing the Harmonics List Display (Option)78
- Setting the Custom Display80
Chapter 7 Numeric Computation83
- Turning Numeric Measurement on and off83
- Setting the Calculation Period84
- Setting Numeric Data Averaging85
- Setting User-Defined Functions86
- Setting Apparent Power, Reactive Power, and Corrected Power Equations88
- Setting the Phase Difference Display Format90
- Setting Harmonic Measurement Conditions91
Chapter 8 Waveform Display92
- Setting the Waveform Display92
- Using the Snapshot and Clear Trace Features94
Chapter 9 Bar Graph Display (Option)95
- Configuring the Bar Graph Display95
Chapter 10 Vector Display (Option)96
- Configuring the Vector Display96
Chapter 11 X-Y Display97
- Displaying X-Y Waveforms97
Chapter 12 Zooming Waveforms99
- Zooming in on or out of Waveforms99
Chapter 13 Cursor Measurement103
- Measuring with Horizontal Cursors103
- Measuring with Vertical Cursors104
- Measuring with Marker Cursors (Marker)105
- Measuring with Angle Cursors (Degree)107
- Measuring with Horizontal and Vertical Cursors (H & V)108
- Measuring with Peak Cursors (Peak)109
Chapter 14 Automated Measurement of Waveform Parameters110
- Automatically Measuring Waveform Parameters110
- Performing Normal Statistical Processing113
- Performing Cyclic Statistical Processing114
Chapter 15 Waveform Computation116
- Performing Addition, Subtraction, Multiplication, and Division116
- Performing Binary Conversion117
- Shifting the Phase118
- Displaying the Power Spectrum119
- Performing User-Defined Computations120
Chapter 16 FFT120
- Displaying FFT Waveforms123
Chapter 17 GO/NO-GO Determination125
- Performing GO/NO-GO Determination with Waveform Zones125
- Performing GO/NO-GO Determination with Waveform Parameters128
Chapter 18 Action128
- Setting Actions130
Chapter 19 Searching Waveforms132
- Searching for Edges132
- Searching for a Specific Time134
Chapter 20 Displaying and Searching History Waveforms135
- Displaying Waveform History Waveforms135
- Searching History Waveforms137
Chapter 21 Printing and Saving Screen Captures140
- Loading Roll Paper into the Built-In Printer (Optional)140
- Printing on the Built-In Printer (Option)142
- Saving Screen Captures to Files143
Chapter 22 Saving and Loading Data145
- Connecting Storage Media145
- Formatting Storage Media148
- Saving Waveform Data150
- Saving Numeric Data155
- Saving Setup Data158
- Saving Other Types of Data159
- Loading Waveform Data163
- Loading Setup Data164
- Loading Other Types of Data165
- Performing File Operations166
- Display Format167
Chapter 23 Ethernet Communication173
- Connecting the PX8000 to a Network173
- Connection Procedure174
- Configuring TCP/IP Settings175
- Accessing the PX8000 from a PC (FTP Server)176
- Connecting to a Network Drive177
- Using SNTP to Set the Date and Time178
Chapter 24 Other Operations179
- Calibrating the PX8000179
- Using the NULL Feature180
- Setting Time Synchronization (Option)181
- Changing the Message, Menu, and USB Keyboard Languages182
- Adjusting the Backlight183
- Initializing the Settings184
- Configuring the Environment Settings185
- Storing and Recalling Setup Data187
- Locking the Keys188

Brand	YOKOGAWA
Model	PX8000
Category	Measuring Instruments
Language	English

YOKOGAWA PX8000 User Manual

Table of Contents

Questions and Answers:

YOKOGAWA PX8000 Specifications

Related product manuals