RESTRICTED USE ONLY Fargo Electronics, Inc.
DTC400e Card Printer User Guide (L001172 Rev. 1.1)
12-3
Download, 11-5
DPI (Dot Per Inch), 11-5
DRAM (Dynamic Random Access Memory), 11-5
Driver, 11-5
DTC400/DTDTC400e0/DTDTC400e0M Card Printer, 8-
1
Duplex Printing, 11-5
Dwell Time, 11-6
Dye Migration, 11-6
Dye-Sub Intensity setting, 4-44
Dye-Sublimation, 2-5, 11-6
Dye-Sublimation Cyan Panel, 2-7
Dye-Sublimation Magenta Panel, 2-7
Dye-Sublimation Yellow Panel, 2-7
Dye-Sublimation-Only Print Ribbons, 2-9
E
E-card, 11-6
E-card Docking Station, 11-6
ECP Mode (Enhanced Capabilities Port Mode), 11-6
Edge-to-Edge, 11-6
EE Memory, 11-6
EEPROM (Electrically Erasable Programmable Read
Only Memory), 11-6
embedded contaminants, 2-11, 4-41
Emissions Standards, 2-2
Encoder (smart card), 11-6
Encoder (wheel), 11-7
Encoding Mode, 6-54
End Sentinel (ES)., 6-66
Engine, 11-7
EOF (End Of Form), 11-7
EPP (Enhanced Parallel Port), 11-7
EPROM (Electronically Programmable Read Only
Memory), 11-7
EPROM version number, 4-54, 4-56
Escape sequence, 11-7
ESD, 1-2, 6-1, 7-1
ESD (ElectroStatic Discharge), 11-7
Ethernet, 11-7
excessive resin printing problems, 4-47
exposed to static electrical discharges, 7-2
F
Fargo Technical Support, 10-1
Fargo Technical Support via the Web, 10-1
FCC, 2-1
feed card into encoder, 4-3
Field Separator (FS), 6-66
Film, 11-7
Firmware, 11-7
Flash Memory, 11-8
Flipper Table Module, 2-12
Font, 11-8
For Overlay Only, 6-76
For Print and Overlay, 6-76
FPGA (Field Programmable Gate Array), 11-8
Front and Back radio buttons, 2-12
Front Cover, 2-6
Frontside and Backside options
K Panel Resin, 6-93, 6-94, 6-95
Overlay / Print Area, 6-71
Full bleed, 11-8
Full Card option, 6-74, 6-97
G
Gamma, 11-8
Glossy / Matte, 11-8
Glossy PVC, 11-8
Graphical Device Interface (GDI), 11-8
Gray Scale, 11-8
H
Halftoning, 11-8
Hard Drive, 11-9
hard Drive space
adequate or inadequate, 4-3
HDP (High Definition Printing™), 11-9
Head, 11-9
Headlift Motors, 4-31
Headlift Sensors, 4-31
Heat Seal, 11-9
Heat sink, 11-9
HiCo (High Coercivity), 11-9
High Coercivity UltraCard IIIs, 6-54
high-resolution, 24-bit color images, 4-53
Horizontal adjustment, 6-43
HTML (HyperText Markup Language), 11-9
HTTP (HyperText Transfer Protocol), 11-9
Humidity, 2-2
I
IC (Integrated Circuit), 11-9
ID (Identification), 11-9
ID format, 6-31
ID software applications, 6-66
Identification Card sample, 6-101
IEEE 1284 (Institute of Electrical and Electronics
Engineers 1284), 11-10
Image, 11-10
Image Color tab, 6-29, 6-37
Image Darkness option, 6-112
Image Placement, 4-51, 4-52
Image Placement option, 6-113
image placement problems, 4-51
Image Placement value, 6-113
Image Position controls, 6-42
inches or mm option, 6-2
incorrect image darkness problems, 4-43
increase Printhead heat, 6-112
Input, 11-10
Input Hopper, 11-10
Interface, 2-2
Intermediate Transfer Media (InTM), 11-10
internal Printer settings, 6-41
ISO, 11-10
ISO 7811-2 Magnetic Stripe, 6-65
ISO encoded data format, 6-57
ISO option, 6-54
To Next Page
Loading...
Need help?
General
