EasyManuals Logo

Huawei SmartAX MA5608T User Manual

Huawei SmartAX MA5608T
1979 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #1836 background imageLoading...
Page #1836 background image
lineprofile-id
10 desc MA5621_0/3/1/1_lineprofile10
To automatically find an ONU, do as follows:
huawei(config)#interface gpon 0/3
huawei(config-if-gpon-0/3)#port 1 ont-auto-find enable
huawei(config-if-gpon-0/3)#display ont autofind 1
//After this command is executed, the information about all ONUs
connected to
//the GPON port through the optical splitter is displayed.
------------------------------------------------------------
Number : 1
F/S/P : 0/3/1
Ont SN : 48575443E6D8B541
Password :
VenderID : HWTC
Ont Version : MA5621
Ont SoftwareVersion : V800R310C00
Ont EquipmentID : SmartAX MA5621
Ont autofind time : 2011-09-10 11:20:16
------------------------------------------------------------
huawei(config-if-gpon-0/3)#ont confirm 1 ontid 1 sn-auth 48575443E6D8B541
snmp ont-lineprofile-id
10 desc MA5621_0/3/1/1_lineprofile10
NOTE
If multiple ONUs of the same type are connected to a port and the same line profile or service profile
is bound to the ONUs, you can add ONUs in batches by confirming the auto-found ONUs in batches
to simplify the operation and increase the configuration efficiency. For example, the preceding
command can be modified as follows:
huawei(config-if-gpon-0/3)#ont confirm 1 all sn-auth snmp ont-lineprofile-id 10 desc
MA5621_0/3/1_lineprofile10
5. Confirm that the ONU goes online normally.
After an ONU is added, run the display ont info command to query the current status of
the ONU. Ensure that Control flag of the ONU is active, Run State is online, and Config
state is normal.
huawei(config-if-gpon-0/3)#display ont info 1 1
---------------------------------------------------------------------
F/S/P :
0/3/1
ONT-ID :
1
Control flag : active //Indicates that the ONU is
activated.
Run state : online //Indicates that the ONU already goes online
normally.
Config state : normal //Indicates that the configuration status
of the ONU is normal.
...//The rest of the response information is omitted.
huawei(config-if-gpon-0/3)#quit
If the ONU state fails, the ONU fails to be in the up state, or the ONU does not match,
check the ONU state by referring to the above-mentioned descriptions.
l If Control flag is deactive, run the ont activate command in the GPON port mode to
activate the ONU.
SmartAX MA5600T/MA5603T/MA5608T Multi-service
Access Module
Commissioning and Configuration Guide
17 Electrical Service Configuration
Issue 01 (2014-04-30) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
1811

Table of Contents

Other manuals for Huawei SmartAX MA5608T

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Huawei SmartAX MA5608T and is the answer not in the manual?

Huawei SmartAX MA5608T Specifications

General IconGeneral
Dual Power SupplyYes
Humidity5% to 95% (non-condensing)
Uplink Slots2
Maximum GPON Ports16
Input Voltage Range-38.4 V DC to -72 V DC
Device TypeOLT
Power Supply-48 V DC
Operating Temperature-25°C to +55°C
Storage Temperature-40°C to 70°C
Switching Capacity128 Gbps
PortsGPON, XG-PON, 10GE

Related product manuals