...//The rest of the response information is not provided here.
huawei(config-if-gpon-0/2)#quit
Step 4 Configure the inband management VLAN and IP address of the OLT.
huawei(config)#vlan 8 smart
huawei(config)#port vlan 8 0/19 0
huawei(config)#vlan priority 8 6
huawei(config)#interface vlanif 8
huawei(config-if-vlanif8)#ip address 192.168.50.1 24
huawei(config-if-vlanif8)#quit
Step 5 Configure the inband management VLAN and IP address of the ONU.
huawei(config)#interface gpon 0/2
huawei(config-if-gpon-0/2)#ont ipconfig 1 1 static ip-address 192.168.50.2 mask
255.255.255.0 gateway
192.168.50.1 vlan 8
huawei(config-if-gpon-0/2)#quit
Step 6 Configure an inband management service port.
huawei(config)#service-port 1 vlan 8 gpon 0/2/1 ont 1 gemport 11 multi-service
user-vlan 8 rx-cttr 6 tx-cttr 6
Step 7 Confirm that the management channel between the OLT and the ONU is available.
l On the OLT, run the ping 192.168.50.2 command to check the connectivity between the
OLT and the ONU. The ICMP ECHO-REPLY packet from the ONU should be received.
l On the OLT, you can remote log in to the ONU to perform the configuration.
Step 8 Configure the channel for the Internet access service.
huawei(config)#vlan 100 smart
huawei(config)#vlan attrib 100 stacking
huawei(config)#port vlan 100 0/19 0
huawei(config)#service-port 101 vlan 100 gpon 0/2/1 ont 1 gemport 12 multi-
service
user-vlan 1001 tag-transform translate-and-add inner-vlan 258 rx-cttr 6 tx-cttr 6
Step 9 Configure the channel for the VoIP service.
huawei(config)#vlan 200 smart
huawei(config)#port vlan 200 0/19 0
huawei(config)#traffic table ip index 9 cir off priority 5 priority-policy local-
setting
huawei(config)#service-port 201 vlan 200 gpon 0/2/1 ont 1 gemport 13 multi-
service
user-vlan 200 rx-cttr 9 tx-cttr 9
Step 10 Configure LAG for upstream ports.
Configure upstream ports 0/19/0 and 0/19/1 into an aggregation group. Each member port in the
aggregation group allocates packets based on the source MAC address. The working mode is
LACP static aggregation.
huawei(config)#link-aggregation 0/19 0-1 ingress workmode lacp-static
Step 11 (Optional) When PPPoE is adopted, enable forwarding the packets with PITP tag on the OLT
equipment.
huawei(config)#pitp permit-forwarding service-port 101 enable
Step 12 (Optional) When IPoE is adopted, enable forwarding the packets with DHCP option on the OLT
equipment.
huawei(config)#dhcp-option82 permit-forwarding service-port 101 enable //For IPv4
packets
huawei(config)#dhcpv6-option permit-forwarding port 0/2/1 ontid 1 enable //For
IPv6 packets
SmartAX MA5600T/MA5603T/MA5608T Multi-service
Access Module
Commissioning and Configuration Guide
19 IPv6 Configuration
Issue 01 (2014-04-30) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
1895
To Next Page
Loading...
Need help?
General
