Step 13 Save the configuration data on the OLT.
huawei(config)#save
Step 14 Log in to and configure the ONU.
You can remote log in to the ONU from the OLT to perform the configuration. By default, the
user name is root and the password is mduadmin.
NOTE
The following steps are configured on the ONU side.
Step 15 Configuration the HSI service on the ONU side.
NOTE
This example creates one service port as an example. Each service port maps a user. When configuring
another service port, map the corresponding SVLAN.
huawei(config)#vlan 1001-1016 smart
huawei(config)#port vlan 1001-1016 0/0 1
huawei(config)#traffic table ip index 8 cir 4096 priority 0 priority-policy local-
Setting
huawei(config)#service-port 101 vlan 1001 eth 0/3/1 multi-service user-vlan
untagged rx-cttr 8 tx-cttr 8
Step 16 (Optional) Configure the PITP function for PPPoE.
huawei(config)#raio-mode common pitp-pmode
huawei(config)#pitp enable pmode
Step 17 (Optional) Configure the DHCP option function for IPoE.
huawei(config)#raio-mode common dhcp-option82 //For DHCPv4 packets
huawei(config)#dhcp option82 enable //For DHCPv4 packets
huawei(config)#raio-mode common dhcpv6-option //For DHCPv6 packets
huawei(config)#dhcpv6 option enable //For DHCPv6 packets
Step 18 Configure the voice service.
huawei(config)#vlan 200 smart
huawei(config)#port vlan 200 0/0 1
huawei(config)#interface vlanif 200
huawei(config-if-vlanif200)#ip address 11.11.11.11 24
huawei(config-if-vlanif200)#quit
huawei(config)#voip
huawei(config-voip)#ip address media 11.11.11.11 11.11.11.11
huawei(config-voip)#ip address signaling 11.11.11.11
huawei(config-voip)#quit
huawei(config)#ip route-static 200.200.200.0 24 11.11.11.11
huawei(config)#interface h248 0
Are you sure to add MG interface?(y/n)[n]:y
huawei(config-if-h248-0)#if-h248 attribute mgip 11.11.11.11 mgport
2944 code text transfer udp primary-mgc-ip1 200.200.200.200 primary-mgc-port
2944 mg-media-ip1 11.11.11.11 start-negotiate-version 1
huawei(config-if-h248-0)#reset coldstart
Are you sure to reset MG interface?(y/n)[n]:y
huawei(config-if-h248-0)#quit
huawei(config)#esl user
huawei(config-esl-user)#mgpstnuser batadd 0/3/0 0/3/23 0 terminalid 0 telno
83110001
huawei(config-esl-user)#mgpstnuser modify 0/3/0 priority cat2
huawei(config-esl-user)#quit
huawei(config)#pstnport
huawei(config-pstnport)#pstnport attribute batset 0/3/0 0/3/23 reverse-pole-pulse
enable
huawei(config-pstnport)#quit
Step 19 Save the configuration on the ONU side.
SmartAX MA5600T/MA5603T/MA5608T Multi-service
Access Module
Commissioning and Configuration Guide
19 IPv6 Configuration
Issue 01 (2014-04-30) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
1896
To Next Page
Loading...
Need help?
General
