Huawei SmartAX MA5608T User Manual

1. Configure the IP address of the loopback interface.
Configure the IP address of loopback interface 0 to 5.5.5.5/32.
huawei(config)#interface loopback 0
huawei(config-if-loopback0)#ip address 5.5.5.5 32
huawei(config-if-loopback0)#quit
2. Configure the LSR ID of the MPLS and enable global MPLS TE and Layer 2 VPN.
huawei(config)#mpls lsr-id 5.5.5.5
huawei(config)#mpls
huawei(config-mpls)#mpls te
huawei(config-mpls)#mpls rsvp-te
huawei(config-mpls)#quit
huawei(config)#mpls l2vpn
3. Enable the VLAN interface MPLS TE function and configure the IP address of the VLAN
interface.
huawei(config)#mpls vlan 300
huawei(config)#interface vlanif 300
huawei(config-if-vlanif300)#ip address 192.168.2.20 24
huawei(config-if-vlanif300)#mpls
huawei(config-if-vlanif300)#mpls te
huawei(config-if-vlanif300)#mpls rsvp-te
huawei(config-if-vlanif300)#quit
Step 3 Configure a route.
PWE3 has no special requirement for the routing policy. Either a static route or an OSPF dynamic
route can be configured. Because OSPF supports MPLS RSVP-TE extension, an OSPF dynamic
route is recommended.
huawei(config)#ospf 1
huawei(config-ospf-1)#opaque-capability enable..//Enable the opaque capability
huawei(config-ospf-1)#area 200
huawei(config-ospf-1-area-0.0.0.200)#mpls-te enable standard-complying //Enable
MPLS TE for the OSPF area
huawei(config-ospf-1-area-0.0.0.200)#network 192.168.2.0 0.0.0.255
huawei(config-ospf-1-area-0.0.0.200)#network 5.5.5.5 0.0.0.0
huawei(config-ospf-1-area-0.0.0.200)#return
Step 4 Configure a PWE3 outer tunnel.
Configure the tunnel ID to 20 and the encapsulation protocol of the tunnel interface at the data
link layer to MPLS TE.
huawei#config
huawei(config)#interface tunnel 20
huawei(config-if-tunnel20)#tunnel-protocol mpls te
Configure the destination IP address of the tunnel to 7.7.7.7.
huawei(config-if-tunnel10)#destination 7.7.7.7
Configure the ID of the MPLS TE tunnel interface to 20. The tunnel ID and LSR ID uniquely
identify an MPLS TE tunnel.
huawei(config-if-tunnel20)#mpls te tunnel-id 20
Configure the signaling protocol of the MPLS TE tunnel to RSVP-TE.
huawei(config-if-tunnel20)#mpls te signal-protocol rsvp-te
Configure the MPLS TE tunnel for being bound by a VPN instance.
huawei(config-if-tunnel20)#mpls te reserved-for-binding
SmartAX MA5600T/MA5603T/MA5608T Multi-service
Access Module
Commissioning and Configuration Guide
4 Configuration Example of the Private Line Service
Issue 01 (2014-04-30) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
411

Huawei SmartAX MA5608T Specifications

General

Dual Power Supply	Yes
Humidity	5% to 95% (non-condensing)
Uplink Slots	2
Maximum GPON Ports	16
Input Voltage Range	-38.4 V DC to -72 V DC
Device Type	OLT
Power Supply	-48 V DC
Operating Temperature	-25°C to +55°C
Storage Temperature	-40°C to 70°C
Switching Capacity	128 Gbps
Ports	GPON, XG-PON, 10GE