Huawei SmartAX MA5608T User Manual

huawei(config-if-vlanif200)#mpls
huawei(config-if-vlanif200)#mpls te
huawei(config-if-vlanif200)#mpls rsvp-te
huawei(config-if-vlanif200)#quit
Step 3 Configure a route.
PWE3 has no special requirement for the routing policy. Either a static route or an OSPF dynamic
route can be configured. Because OSPF supports MPLS RSVP-TE extension, an OSPF dynamic
route is recommended.
huawei(config)#ospf 1
huawei(config-ospf-1)#opaque-capability enable..//Enable the opaque capability
huawei(config-ospf-1)#area 100
huawei(config-ospf-1-area-0.0.0.100)#mpls-te enable standard-complying //Enable
MPLS TE for the OSPF area
huawei(config-ospf-1-area-0.0.0.100)#network 192.168.1.0 0.0.0.255
huawei(config-ospf-1-area-0.0.0.100)#network 5.5.5.5 0.0.0.0
huawei(config-ospf-1-area-0.0.0.100)#return
Step 4 Configure a PWE3 outer tunnel.
Configure the tunnel ID to 10 and the encapsulation protocol of the tunnel interface at the data
link layer to MPLS TE.
huawei#config
huawei(config)#interface tunnel 10
huawei(config-if-tunnel10)#tunnel-protocol mpls te
Configure the destination IP address of the tunnel to 6.6.6.6.
huawei(config-if-tunnel10)#destination 6.6.6.6
Configure the ID of the MPLS TE tunnel interface to 10. The tunnel ID and LSR ID uniquely
identify an MPLS TE tunnel.
huawei(config-if-tunnel10)#mpls te tunnel-id 10
Configure the signaling protocol of the MPLS TE tunnel to RSVP-TE.
huawei(config-if-tunnel10)#mpls te signal-protocol rsvp-te
Configure the MPLS TE tunnel for being bound by a VPN instance.
huawei(config-if-tunnel10)#mpls te reserved-for-binding
Commit the configuration and quit the tunnel configuration.
huawei(config-if-tunnel10)#mpls te commit
huawei(config-if-tunnel10)#quit
Step 5 Configure the tunnel policy.
Configure the policy name to ethpw-plcy.
huawei(config)#tunnel-policy ethpw-plcy
Info: New tunnel-policy is configured.
huawei(config-tunnel-policy-ethpw-plcy)#tunnel binding destination 6.6.6.6 te
tunnel 10
huawei(config-tunnel-policy-ethpw-plcy)#quit
Step 6 Configure the PW parameters.
1. Configure the PW ID to 10.
huawei(config)#pw-para 10
SmartAX MA5600T/MA5603T/MA5608T Multi-service
Access Module
Commissioning and Configuration Guide
4 Configuration Example of the Private Line Service
Issue 01 (2014-04-30) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
417

Huawei SmartAX MA5608T Specifications

General

Dual Power Supply	Yes
Humidity	5% to 95% (non-condensing)
Uplink Slots	2
Maximum GPON Ports	16
Input Voltage Range	-38.4 V DC to -72 V DC
Device Type	OLT
Power Supply	-48 V DC
Operating Temperature	-25°C to +55°C
Storage Temperature	-40°C to 70°C
Switching Capacity	128 Gbps
Ports	GPON, XG-PON, 10GE