huawei(config-acl-adv-3050)#rule permit ip source 4.4.4.4 0.0.0.0
destination 10.10.1.2 0.0.0.0
huawei(config-acl-adv-3050)#rule permit ip source 4.4.4.5 0.0.0.0
destination 10.10.1.2 0.0.0.0
huawei(config-acl-adv-3050)#rule permit ip source 3.3.3.3 0.0.0.0
destination 10.10.1.2 0.0.0.0
huawei(config-acl-adv-3050)#rule permit ip source 3.3.4.3 0.0.0.0
destination 10.10.1.2 0.0.0.0
huawei(config-acl-adv-3050)#quit
huawei(config)#packet-filter inbound ip-group 3050 port 0/19/1
huawei(config)#packet-filter inbound ip-group 3050 port 0/20/0
4. Configure the SNMP parameters.
l Configure the community name and the access authority.
huawei(config)#snmp-agent community read public
huawei(config)#snmp-agent community write private
l Configure the contact information.
huawei(config)#snmp-agent sys-info contact HW-075512345678
l Configure the device location information.
huawei(config)#snmp-agent sys-info location Shenzhen China
l Configure the SNMP version.
The SNMP version must be the same as the SNMP version of the NMS. In this
example, the NMS version is set as SNMP v2c.
huawei(config)#snmp-agent sys-info version v2c
5. Enable the trap sending.
huawei(config)#snmp-agent trap enable standard
6. Set the trap destination address.
huawei(config)#snmp-agent target-host trap-hostname huawei address 2.2.2.2
trap-paramsname abc
huawei(config)#snmp-agent target-host trap-hostname huawei123 address 2.2.2.3
trap-paramsname 123
7. Set the trap source address.
huawei(config)#snmp-agent trap source vlanif 10
Step 3 Configure the time server.
huawei(config)#ntp-service unicast-server 4.4.4.4 source-interface vlanif 10
huawei(config)#ntp-service unicast-server 4.4.4.5 source-interface vlanif 10
Step 4 Configure the log host.
huawei(config)#loghost add 3.3.3.3 syslog-1
huawei(config)#loghost activate ip 3.3.3.3
huawei(config)#loghost add 3.3.4.3 syslog-2
huawei(config)#loghost activate ip 3.3.4.3
Step 5 Configure the EMU.
This topic uses the fan and PS4875L power supply as an example to describe how to configure
the environment monitoring unit (EMU).
By default, the default slave node number of the fan EMU is 0. In this example, suppose the
slave node number is 1. In this case, you need to set the DIP switch of the slave node number
on the fan monitoring unit as 1.
huawei(config)#emu add 0 power4875l 0 0
huawei(config)#emu add 1 fan 0 1
huawei(config)#interface emu 0
huawei(config-if-power4875l-0)#power module-num 2 1 2
huawei(config-if-power4875l-0)#quit
SmartAX MA5600T/MA5603T/MA5608T Multi-service
Access Module
Commissioning and Configuration Guide
5 Configuration Example of MSTP Subtending Network
Issue 01 (2014-04-30) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
446
To Next Page
Loading...
Need help?
General
