Huawei SmartAX MA5608T User Manual

Step 6 Configure GIU subtending
MA5600T/MA5603T/MA5608T-1 is subtended with MA5600T/MA5603T/MA5608T-2,
MA5600T/MA5603T/MA5608T-3 and MA5600T/MA5603T/MA5608T-4. Therefore,
subtending should be configured.
huawei(config)#vlan 60 to 62 standard
huawei(config)#port vlan 60 to 62 0/19 0-2
huawei(config)#vlan 101 to 102 standard
huawei(config)#port vlan 101 to 102 0/19 0-2
Step 7 Configure MSTP.
1. Enable the MSTP function.
huawei(config)#stp enable
Change global stp state may active region configuration,it may take
several
minutes,are you sure to change global stp state? [Y/N][N]
Y
2. Set the MST region name.
huawei(config)#stp region-configuration
huawei(stp-region-configuration)#region-name hwrg
3. Configure MSTP instance 1.
huawei(stp-region-configuration)#instance 1 vlan 1 to 4094
4. Activate the configuration of the MST region.
huawei(stp-region-configuration)#active region-configuration
STP actives region configuration, it may take several minutes,are you sure
to
active region configuration? [Y/N][N]y
5. Set the priority of MA5600T/MA5603T/MA5608T_1 in the instance.
huawei(stp-region-configuration)#quit
huawei(config)#stp instance 0 priority 0
huawei(config)#stp instance 1 priority 0
Step 8 Configure ADSL2+ service.
The MA5600T/MA5603T/MA5608T supports the ADSL2+ service of multiple encapsulation
modes, such as IPoA, PPPoA, IPoE, and PPPoE. This topic uses the PPPoE mode as an example
to describe how to configure the ADSL2+ service. For other encapsulation modes, see "3.1
Example: Configuring the xDSL Internet Access Service."
1. Configure the ADSL2+ line profile.
You can configure the ADSL2+ line profile based on your requirements.
huawei(config)#adsl line-profile add 10
Start adding
profile
Press 'Q' to quit the current configuration and new configuration will
be
neglected
> Do you want to name the profile (y/n)
[n]:
> Transmission
mode:
> 0:
Custom
> 1: All (G.
992.1~5,T1.413,ETSI)
> 2: Full rate(G.
992.1/3/5,T1.413,ETSI)
> 3: G.DMT (G.
992.1/3/5)
SmartAX MA5600T/MA5603T/MA5608T Multi-service
Access Module
Commissioning and Configuration Guide
5 Configuration Example of MSTP Subtending Network
Issue 01 (2014-04-30) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
447

Huawei SmartAX MA5608T Specifications

General

Dual Power Supply	Yes
Humidity	5% to 95% (non-condensing)
Uplink Slots	2
Maximum GPON Ports	16
Input Voltage Range	-38.4 V DC to -72 V DC
Device Type	OLT
Power Supply	-48 V DC
Operating Temperature	-25°C to +55°C
Storage Temperature	-40°C to 70°C
Switching Capacity	128 Gbps
Ports	GPON, XG-PON, 10GE