Busy LED 88
C
Caller ID Stack 56
Changing Configuration Data of 1 RF Deck
While
a System in a Multi RF Deck/ Multi Control
Head Structure Is Operating
372
Changing Configuration Data While a System in
a
Multi RF Deck/ Multi Control Head Structure Is
Operating
366
Changing the Brightness of the Backlight (LCD
Brightness)
93
Changing the Channel 41
Changing the Channel by Specifying the
Number (Channel Entry)
42
Changing the Channel with a Single Touch 45
Changing the Color Scheme of the Transceiver
Display (Color Scheme)
94
Changing the Configuration of the Transceiver
(Front Panel Programming Mode)
243
Changing the Display Positions of a Channel
Name
and an Icon When Multi RF Deck View Is
On
375
Changing the Group ID by Specifying the ID
(Group
ID Entry) (NXDN Trunking System Only)
44
Changing the Tone Volume Level with a Single
Touch (Selectable Tone Level)
122
Changing the Zone 40
Changing the Zone-channel 40
Channel Spacing 80
Character Entry 69
Checking the Bluetooth Device Name (Bluetooth
Information)
181, 308
Checking the Detailed Information of a Battery
(Battery Information Display)
149
Checking the Firmware Version (Transceiver
Information Mode)
245
Clear Caller ID Stack on Reply 57
Clock Display 103
COM Port Functions 423
Communicating Directly Between Control Heads
(Intercom)
282
Communication Ports 296
Communications in an Emergency (Emergency) 302
Conditions to Activate the Horn Alert 230
CONFIGURATION FOR EACH FUNCTION 393
Configuration in KPG-D1/ D1N If Changed from
a Multi RF Deck System to a Single RF Deck
Structure
385
Configuration in KPG-D1/ D1N If Changed from
a Single RF Deck Structure to a Multi RF Deck
System
378
Configuration in KPG-D1/ D1N If Control Heads
Are Switched
384
Configuration in KPG-D1/ D1N if RF Decks Are
Switched
381
Configuring Audio Profile (Audio Profile) 127
Configuring Mobile Relay Station 325
Configuring Recording Time (Maximum
Recording Length)
163
Configuring the Alert Tone (Alert Tone Pattern) 117
Configuring the Bluetooth Device Name of the
Transceiver (Bluetooth Device Name)
180
Configuring the Connection Destination of a
Bluetooth-compatible Device (Bluetooth
Interface Selection)
207
Configuring the DIP Switch 258
Configuring the Display Order of Data in Stack
Mode (Stack Order)
54
Configuring the FPU Data and Writing the FPU
Data to Each RF Deck
252
Configuring the GPS Position Display 150
Configuring the Initial Configuration 249
Configuring the Input Sensitivity of the
Microphone (VOX Gain Level)
390
Configuring the Maximum Volume Level
(Maximum Volume)
120
Configuring the Minimum Volume Level
(Minimum Volume)
120
Configuring the Offset Value for Volume Level
(Tone Volume Offset)
121
Configuring the Output Method of the Received
Audio and Beep (Multi RF Deck Audio Output
Type)
288
Configuring the Storage Method of an Audio
Data File (First-in First-out Deletion)
159
Configuring the Volume Level of Various Tones
(Tone Volume)
121
Configuring the Warning Behavior for the
Remaining Memory Capacity (Low Memory
Warning)
158
Configuring Voice Guidance Method (Voice
Announcement Type)
138
Confirming microSD Card Contents via a PC (SD
Card Direct Access)
173
Connecting by Headset Profile 197
Connecting by Serial Port Profile 202
Connecting the External Microphone 388
Connecting the External Speaker 332, 388
Connecting the RF Deck by Using a D-sub 25-
pin Cable
327
Connecting the Transceiver to a PC 21
INDEX
Common FUNC (K, F)/Ver 2.20 441
CONTENTS INDEX
To Next Page
Loading...
Need help?
General
