Keysight N1913 - Page 21

Keysight N1913/1914A User’s Guide 21
Figure 2-52 Password reconfirmation pop-up . . . . . . . . . . . . . . .116
Figure 2-53 Enter password to restore display . . . . . . . . . . . . . . .117
Figure 2-54 Backlight intensity control . . . . . . . . . . . . . . . . . . . . .118
Figure 2-55 Increase or decrease the backlight brightness . . . . .118
Figure 2-56 Activate memory erase using combo keys . . . . . . . .119
Figure 2-57 Secure Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120
Figure 2-58 Confirmation to begin secure erase . . . . . . . . . . . . . .120
Figure 2-59 Warning pop-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121
Figure 2-60 VGA toggle ON/OFF . . . . . . . . . . . . . . . . . . . . . . . . . .122
Figure 2-61 Enable/disable warm start feature . . . . . . . . . . . . . .123
Figure 2-62 “Running under battery power” pop-up . . . . . . . . . .124
Figure 2-63 Battery indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125
Figure 2-64 Battery menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125
Figure 2-65 Battery status display . . . . . . . . . . . . . . . . . . . . . . . . .126
Figure 2-66 Low battery indicator . . . . . . . . . . . . . . . . . . . . . . . . .126
Figure 2-67 Display backlight control . . . . . . . . . . . . . . . . . . . . . .127
Figure 2-68 Short/long cable option . . . . . . . . . . . . . . . . . . . . . . .130
Figure 3-1 E9300 E-Series auto-averaging settings . . . . . . . . . .133
Figure 3-2 . . . . . E9300 E-Series sensor default channel setup 134
Figure 3-3 Frequency pop-up . . . . . . . . . . . . . . . . . . . . . . . . . . .137
Figure 3-4 Spread spectrum signal . . . . . . . . . . . . . . . . . . . . . . .138
Figure 3-5 Wideband CDMA error of E-Series E9300 power sensor
versus corrected CW sensor . . . . . . . . . . . . . . . . .139
Figure 3-6 CDMA (IS-95A): 9Ch Fwd . . . . . . . . . . . . . . . . . . . . .139
Figure 3-7 Calibration factors versus frequency . . . . . . . . . . . . .140
Figure 4-1 E-Series CW sensor auto-averaging settings . . . . . .149
Figure 4-2 E-Series E4410 sensor default channel setup . . . . . .150
Figure 4-3 Frequency pop-up . . . . . . . . . . . . . . . . . . . . . . . . . . .152
Figure 5-1 8480 Series auto-averaging settings . . . . . . . . . . . . .155
Figure 5-2 8480 Series sensor default channel setup . . . . . . . . .156
Figure 5-3 Reference Calibration Factor pop-up window . . . . .160
Figure 5-4 Calibration factor pop-up window . . . . . . . . . . . . . . .161
Figure 5-5 Calibration factor display . . . . . . . . . . . . . . . . . . . . . .161
Figure 5-6 Sensor table selected . . . . . . . . . . . . . . . . . . . . . . . . .164
Figure 5-7 Frequency dependent offset indicator . . . . . . . . . . . .164
Figure 5-8 Frequency/calibration table display . . . . . . . . . . . . .165
Figure 5-9 “Sensor Tbls” screen . . . . . . . . . . . . . . . . . . . . . . . . .167