Leader LT4670 - Page 191

217 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

16 WEB BROWSER

178

Table of Contents

Default Chapter2
- Table of Contents2
General Safety Summary10
1 Introduction14
- User Registration14
- Scope of Warranty14
- Trademark Acknowledgments14
- Operating Precautions15
2 Product Configuration16
- Main Unit16
- Hardware Options16
- Software Options17
3 Specifications18
- General18
- Features18
- Standards24
4 Panel Description43
- Front Panel43
- Rear Panel46
5 Preparations49
- Turning the Power on49
- Rack Mounting53
6 Basic Operation54
- Operation Basics54
- Signal Input (Genlock Operation)58
- SDI Signal Output68
- LTC Signal I/O and Remote Control71
- Alarm Display73
- L-Sync74
7 Reference Config Menu76
- Selecting the Reference Signal76
- Selecting the Genlock Format77
- Setting the Genlock Timing78
- Selecting the Satellite (SER01)78
- Setting the Recovery Operation79
- Setting the Relock80
- Selecting the Time Source81
- Loading the Date and Time82
8 Black Config Menu83
- Selecting the Black Format83
- Configuring Timing Data84
- Setting the Time Code85
  - Turning Time Code Insertion on and off85
  - Setting Dropped Frames86
- Setting the Black Output86
  - Turning the Black Output on and off86
  - Turning BMCA Linkage on and off (SER03)87
- Settings Shared by Black Outputs87
9 Audio Config Menu88
- Setting the AES/EBU Output88
- Setting the Silence Output91
- Setting the Word-Clock Output93
  - Adjusting the Timing93
10 Ltc Config Menu94
- Turning the LTC Output on and off94
- Selecting the LTC Format94
- Adjusting the Timing (Frame)95
- Adjusting the Timing (Bit)95
- Adjusting the Offset95
- Setting Dropped Frames96
- Settings Shared by LTC Outputs96
11 Cw/1Pps Config Menu97
- Switching the Output Signal97
12 Sdi Config Menu (Ser02)98
- Selecting the Frequency Group98
- Setting the SDI Format99
- Configuring Timing Data101
- Selecting the Pattern102
- Turning Ycbcr/Gbr on and off104
- Turning Safety Area Markers on and off105
- Configuring the Pattern Scroll Feature106
- Setting the Pattern Change107
  - Turning Pattern Change on and off107
  - Setting the Change Interval108
- Setting ID Characters108
- Setting the Moving Box116
- Setting a Circle119
- Setting the Time Code122
- Turning Lip Sync on and off124
- Configuring Embedded Audio126
- Setting Ancillary Data130
- Setting the SDI Output131
  - Turning the SDI Output on and off131
  - Turning BMCA Linkage on and off (SER03)132
- Settings Shared by SDI Outputs132
13 Ptp Config Menu (Ser03)133
- PTP Leader and PTP Follower133
- Setting the PTP Leader133
- Setting the PTP Follower140
14 System Config Menu147
- Setting the Backlight147
- Configuring Presets147
- Setting the Network152
- Setting the Time156
- Setting the GNSS (SER01)160
  - Setting the Power Supply160
  - Setting the Cable Delay160
- Configuring the PTP Settings (SER03)161
- Setting the Alarm163
  - Selecting the Polarity163
  - Turning the Alarm Output on and off164
- Configuring the Log165
- Initialization166
- Viewing and Adding Software Options168
  - Viewing Software Options168
  - Adding Software Options168
- Configuring USB169
- Turning the Fans on and off169
- Copying the System Settings170
  - Copying System Settings from a USB Memory Device to the Instrument170
  - Copying System Settings from the Instrument to a USB Memory Device170
15 Status Menu171
- ALARM Menu171
- INFORMATION Menu172
- CONFIG Menu174
- LOG Menu178
  - Viewing the Log178
  - Clearing the Log178
16 Web Browser179
- Operating Environment179
- How to Use179
- Procedure181
- Screen Description183
17 Maintenance201
- Calibration and Repair201
- Replacement of Parts201
18 Appendix209
- List of Settings209
- Release Notes216

Other manuals for Leader LT4670

Instructions13 pages

Related product manuals

Preview: Leader LSG-16