Lenze i410 - Page 316

Address Name Default seng Category Data type Factor A M
0x261C:043
(P740.43)
Favorites
sengs: Parameter 43 0x26390100 general IDX 1 PH -
0x261C:044
(P740.44)
Favorites sengs: Parameter 44 0x26390200 general IDX 1 PH -
0x261C:045
(P740.45)
Favorites sengs: Parameter 45 0x26390300 general IDX 1 PH -
0x261C:046
(P740.46)
Favorites sengs: Parameter 46 0x26390400 general IDX 1 PH -
0x261C:047
(P740.47)
Favorites sengs: Parameter 47 0x29110100 general IDX 1 PH -
0x261C:048
(P740.48)
Favorites sengs: Parameter 48 0x29110200 general IDX 1 PH -
0x261C:049
(P740.49)
Favorites sengs: Parameter 49 0x29110300 general IDX 1 PH -
0x261C:050
(P740.50)
Favorites sengs: Parameter 50 0x29110400 general IDX 1 PH -
0x2630:002
(P410.02)
Sengs for digital inputs: Input funcon Digital input [0] general U8 1 P -
0x2631:001
(P400.01)
Funcon list: Enable inverter Constant TRUE [1] general U8 1 PC -
0x2631:002
(P400.02)
Funcon list: Run Digital input 1 [11] general U8 1 PC -
0x2631:003
(P400.03)
Funcon list: Acvate quick stop Not connected [0] general U8 1 PC -
0x2631:004
(P400.04)
Funcon list: Reset fault Digital input 2 [12] general U8 1 P -
0x2631:005
(P400.05)
Funcon list: Acvate DC braking Not connected [0] general U8 1 P -
0x2631:010
(P400.10)
Funcon list: Jog foward (CW) Not connected [0] general U8 1 PC -
0x2631:011
(P400.11)
Funcon list: Jog reverse (CCW) Not connected [0] general U8 1 PC -
0x2631:012
(P400.12)
Funcon list: Acvate keypad control Not connected [0] general U8 1 P -
0x2631:013
(P400.13)
Funcon list: Reverse rotaonal
direcon Digital input 3 [13] general U8 1 PC -
0x2631:014
(P400.14)
Funcon list: Acvate AI1 setpoint Not connected [0] general U8 1 P -
0x2631:015
(P400.15)
Funcon list: Acvate AI2 setpoint Not connected [0] general U8 1 P -
0x2631:016
(P400.16)
Funcon list: Acvate keypad setpoint Not connected [0] general U8 1 P -
0x2631:018
(P400.18)
Funcon list: Acvate preset (bit 0) Digital input 4 [14] general U8 1 P -
0x2631:019
(P400.19)
Funcon list: Acvate preset (bit 1) Digital input 5 [15] general U8 1 P -
0x2631:020
(P400.20)
Funcon list: Acvate preset (bit 2) Not connected [0] general U8 1 P -
0x2631:021
(P400.21)
Funcon list: Acvate preset (bit 3) Not connected [0] general U8 1 P -
0x2631:022
(P400.22)
Funcon list: Acvate setpoint via HTL input Not connected [0] general U8 1 P -
0x2631:023
(P400.23)
Funcon list: MOP setpoint up Not connected [0] general U8 1 P -
0x2631:024
(P400.24)
Funcon list: MOP setpoint down Not connected [0] general U8 1 P -
0x2631:025
(P400.25)
Funcon list: Acvate MOP setpoint Not connected [0] general U8 1 P -
* Default seng dependent on the model.
Appendix
P
arameter aribute list
316