Mold-Masters M2 - Page 5

© 2014 Mold-Masters (2007) Limited. All Rights Reserved.
Revised 1 Oct, 2014
V
www.moldmasters.com
5.2 CREATE A FIRST TOOL ..........................................................................................5-3
5.3 SETUP PAGE - CARDS THAT MAY BE DETECTED...............................................5-4
5.4 PRE-CONFIGURED SETUP VALUES .....................................................................5-5
5.5 HOW TO CONFIGURE THE CONTROL CARDS ....................................................5-6
5.6 SET THE TOOL PARAMETERS...............................................................................5-8
5.7 THE TOOL PARAMETERS ......................................................................................5-9
5.8 CONFIGURE THE TOOL & SYSTEM SETTINGS .................................................5-12
5.9 THE TOOL SETTINGS ..........................................................................................5-13
5.10 THE SYSTEM SETTINGS ....................................................................................5-18
5.11 SET OPERATING PARAMETERS........................................................................5-21
5.11.1 SELECTING ZONES ...................................................................................5-21
5.11.2 TO SET PROBE AND MANIFOLD TEMPERATURES ................................5-23
5.11.3 TO SET SPEAR (BODY AND TIP) TEMPERATURES ................................5-24
5.11.4 TO SET CAVITIES, WATER FLOWS AND CHILLERS ................................5-26
5.12 SAVE EVERYTHING TO A TOOL BANK ..............................................................5-27
5.13 SET UP EASYVIEW PAGES ................................................................................5-28
5.14 PASSWORDS AND USER ACCESS EXPLAINED ..............................................5-31
5.14.1 SET UP USER ACCESS .............................................................................5-32
5.14.2 CONFIGURE USERS ..................................................................................5-34
5.14.3 LIST CURRENT USERS .............................................................................5-35
5.14.4 USER ADMIN OPTIONS .............................................................................5-36
5.14.5 CONFIGURE USER LIMITATIONS .............................................................5-37
5.15 MELT LEAKAGE DETECTION .............................................................................5-38
5.15.1 CONFIGURING AUTO LEAKAGE DETECTION .........................................5-38
5.16 SET TIME AND DATE ..........................................................................................5-40
5.17 UTILITIES - ENERGY PAGE ................................................................................5-41
5.18 PRINT PAGE ........................................................................................................5-42
5.18.1 USING A LOCALLY CONNECTED PRINTER ............................................5-42
5.18.2 USING A REMOTE NETWORK PRINTER .................................................5-42
5.18.3 PRINTING TO A USB MEMORY STICK ......................................................5-42
5.19 EVENT LOG AND EXPORT PAGES ....................................................................5-43
Section 6 - Operation ...........................................................6-1
6.1 LOG IN ....................................................................................................................6-2
6.1.1 LOG OUT .........................................................................................................6-2
6.2 CONTROL MODES FOR ALL ZONES .....................................................................6-3
6.2.1 CONTROL FOR INDIVIDUALLY SELECTED ZONES ....................................6-4
6.3 MORE ABOUT USING BOOST ................................................................................6-5
6.4 USE DISPLAY PAGE TO CHANGE TEMPERATURES ...........................................6-6
6.5 USE THE DISPLAY PAGE TO CHANGE MODES ...................................................6-7
6.6 MORE ABOUT SLAVING ZONES ............................................................................6-8
6.7 ABOUT EASYVIEW PAGE .......................................................................................6-9
6.8 USE EASYVIEW TO CHANGE TEMPERATURES ................................................6-10
6.9 USE EASYVIEW TO CHANGE MODES ................................................................6-11
6.10 PURGE SEQUENCE ............................................................................................6-12
6.11 PRE-SET PURGE PARAMETERS .......................................................................6-13
6.12 CHECK ZONE PAST PERFORMANCE (GRAPH) ...............................................6-14
6.12.1 INSPECTING THE LAST 5 OR 30 MINUTES ............................................6-14
6.12.2 INSPECTING THE LAST 24 HOURS ..........................................................6-15
6.13 THE EVENT LOG PAGE ......................................................................................6-16
6.13.1 BEACON AND SOUNDER EXTENSION ....................................................6-20
6.14 TRAINING AND DEMONSTRATION MODE ........................................................6-21
6.14.1 ABOUT DEMO MODE .................................................................................6-21