Omron E5EK - INDEX

INDEX
E5EK
Symbols
[A/M] key protect 5---4....................
° C/° F selection 5---28.....................
Numbers
100%AT 3---16...........................
40%AT 3---16.............................
A
A g r o u p 6 --- 1 1............................
A / D c o n v e r t e r e r r o r 3 --- 6 , 8 --- 3 , 8 --- 5........
A / M k e y 1 --- 3.............................
A/M key protect 3---12.....................
About Calibration 1---11...................
ABOUT CURRENT
T R A N S F O R M E R ( C T ) A --- 5...........
About invalid parameters 6---7.............
Abo ut parameter display 5---2..............
About PID Parameters 3---17..............
About the Communications
Function 1---10........................
About the Decimal Point of the
Alarm Value 3---11.....................
About the displays 1---3...................
About the power blocks 2---10..............
About the temperature unit 3---4...........
About the unit No. 6---12..................
Adjusting Control Operation 3---14.........
Alarm 1 hysteresis 5---24..................
Alarm 1 open in alarm 5---31...............
A l a r m 1 t y p e 5 --- 3 0.......................
Alarm 2 hysteresis 5---24..................
Alarm 2 open in alarm 5---31...............
A l a r m 2 t y p e 5 --- 3 0.......................
Alarm 3 hysteresis 5---24..................
Alarm 3 open in alarm 5---31...............
A l a r m 3 t y p e 5 --- 3 0.......................
A l a r m h y s t e r e s i s 3 --- 1 0....................
A l a r m t y p e 3 --- 9..........................
Alarm value 3---9.........................
Alarm value 1 5---12......................
Alarm value 2 5---12......................
Alarm value 3 5---12......................
A l f a 5 --- 3 4...............................
A S C I I C O D E L I S T A --- 2 0.................
Assignment example 4---9.................
AT calculated gain 5---35..................
A T Execute/Cancel 5---11..................
A T hysteresis 5 ---36.......................
Auto---tuning (A.T.) 3---16.................
A u t o --- t u r n i n g k e y 1 --- 3...................
A u t o / M a n u a l 4 --- 1 0.......................
Automatic return of display mode 5---36.....
Auxiliary output 2---10....................
Auxiliary output 1 assignment 5---29........
Auxiliary output 2 assignment 5---29........
B
B g r o u p 6 --- 1 1............................
Balance---less, Bump---less Operation 3---14..
B a l a n c e d S t a t u s A --- 1 5....................
Basic Operation Flow 3---2.................
B e f o r e s e t u p 2 --- 3 , 2 --- 4....................
C
Cable connections 6---3....................
Calibrating Current Input 7---9............
Calibrating inputs 1---11..................
Calibrati ng Platinum Resistance
Thermometer 7---7.....................
Calibrating Thermocouple 7---4............
Calibrating transfer output 1 ---11..........
Calibrating Voltage Input 7---10............
Calibration 7---7, 7---9.....................
Calibration : 0 to 10V 7---11................
Calibration data error 8---4................
Calibration item menu 7---3...............
C a l i b r a t i o n M o d e 1 --- 8 , 1 --- 9 , 5 --- 4 6.........
Calibration save mark 7---3................
Calibration: 0 to 5 V, 1 to 5 V 7---10.........
Calibration: thermocouple 1 7---5...........
Calibration: thermocouple 2 7---6...........
Changing the set point 3---14...............
Characteristics A---3.....................
Checking Indication Accuracy 7---12........
Checking Operation Restrictions 8---6......
Close in alarm/open in alarm 3---10.........
Command A---17.........................
Command Configuration 6---5..............
Command List 6---10......................
Commands and R esponses 6---6............
Communication baud rate 5---40...........
Communication data length 5---40..........
Communication parity 5---40...............
Communication stop bit 5---40.............
Communication unit No. 5---40.............
Communications 2---11....................
Communications parameters 6---4..........
Conditions when running a program 6---14..
Connecting the Cold
Junction Conductor 7---4...............
CONTROL BLOCK DIAGRAM A ---6.......
C o n t r o l o u t p u t 2 --- 9.......................