EasyManua.ls Logo

Omron E5EK - Page 172

Omron E5EK
176 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
INDEX
E5EK
Control output 1 assignment 5---28.........
Control output 2 assignment 5---28.........
Control period 3---7.......................
Control period (cool) 5---16................
Control period (heat) 5---16................
Convention Used in this Chapter 3---2......
ConventionsUsedinthisChapter 5---2.....
Cooling coefficient 4---2, 5---13.............
C T i n p u t / P o t e n t i o m e t e r 1 --- 4 , 2 --- 1 0........
C u r r e n t i n p u t 1 --- 4 , 7 --- 1 3.................
D
D e a d b a n d 4 --- 2 , 5 --- 1 4.....................
Decimal point 5---27......................
Derivative time 5---13.....................
Determining the LBA detection time 4---16..
D i m e n s i o n s 2 --- 5 , A --- 5....................
Direct/Reverse operation 3---7, 5 ---31........
Display range over 8---4...................
D o w n k e y 1 --- 3...........................
D r a w --- o u t 2 --- 2...........................
E
E v e n t i n p u t 1 --- 5 , 2 --- 1 1...................
Event input assignment 1 5---39............
Event input assignment 2 5---39............
E x a m p l e s o f u s e 4 --- 1 4 , 6 --- 1 6...............
E x p a n s i o n M o d e 1 --- 7 , 1 --- 9 , 5 --- 3 2..........
F
Fe a t u r e s A --- 1 4..........................
Fixing Screw for Front Panel 2---2..........
Fixing settings 1---9.......................
Fo r m a t A --- 1 7...........................
F r o n t p a n e l 1 --- 2.........................
F U Z Z Y S E L F --- T U N I N G A --- 1 4...........
Fuzzy Self---tuning Function A---14........
H
H B A l a t c h 5 --- 4 2..........................
HBA latch/release 4---13...................
H e a t e r b u r n o u t 5 --- 1 7.....................
Heater burnout detection 4---13............
Heater current monitor 5---17..............
Heating and cooling control 4---2...........
Heter Burnout Alarm A ---3...............
How to calculate the heater burnout
s e t v a l u e 4 --- 1 4........................
How to Read Communications
Error Information 6---12................
How to Use Error Output 8---5.............
H o w t o U s e E v e n t I n p u t 4 --- 8..............
H o w t o u s e k e y s 1 --- 3......................
H o w t o u s e p r o g r a m s 6 --- 1 4................
How to Use the Error Display 8---3.........
How to Use the Heater
Burnout Alarm 4---13..................
HowtoUsetheRemoteSP 4---11...........
How to Use Transfer Output 4 ---17.........
Hysteresis 4 ---4...........................
Hysteresis (cool) 5---15....................
Hysteresis (heat) 5---15....................
I
Initial Checks 8---2........................
I n p u t a n d O u t p u t 1 --- 4....................
Input assignments 4---8...................
Input digital filter 5---23...................
I n p u t e r r o r 3 --- 6 , 8 --- 3.....................
Input errors 8---5.........................
I n p u t s h i f t 3 --- 4..........................
Input shift lower limit 5---24...............
Input shift upper limit 5---24...............
I n p u t t y p e 3 --- 4 , 5 --- 2 6.....................
Installation 2---5..........................
Integral time 5---13.......................
I n t e r f a c e 6 --- 2............................
Issuing special commands 6---10............
L
L B A 4 --- 1 5 , 8 --- 5..........................
LBA detection example 4---15..............
L B A d e t e c t i o n t i m e 4 --- 1 5 , 5 --- 2 1............
L B A d e t e c t i o n w i d t h 4 --- 1 5 , 5 --- 3 6..........
L e v e l 0 M o d e 1 --- 7 , 1 --- 8 , 5 --- 6..............
L e v e l 1 M o d e 1 --- 7 , 1 --- 8 , 5 --- 1 0.............
L e v e l 2 M o d e 1 --- 7 , 1 --- 8 , 5 --- 1 8.............
Limiter operation conditions 4---6..........
M
M a i n p a r t s 1 --- 2..........................
M a n i p u l a t e d v a r i a b l e a t s t o p 3 --- 1 3 , 4 --- 2....
Manipulated variable at
stop/PV error 4---3.....................
Manipulated variable restrictions 4---5......
M a n u a l M o d e 1 --- 7 , 1 --- 9 , 5 --- 5..............
Manual MV 5---5.........................
Manual operation 3---14...................
Manual reset val ue 5---15..................
Memory error 8---3.......................
M e n u d i s p l a y 1 --- 8........................
M O D E L L I S T A --- 1 1.....................
M o n i t o r p r o c e s s v a l u e 6 --- 1 6...............

Table of Contents

Related product manuals