Omron E5EK - Page 173

INDEX
E5EK
Motor Calibration 5---42...................
Motor calibration error 8---4...............
M o u n t i n g 2 --- 6...........................
M u l t i --- S P 4 --- 9...........................
M u l t i --- S P f u n c t i o n 5 --- 3 8..................
MV at PV error 5---21.....................
M V a t s t o p 5 --- 2 1.........................
MV change rate limit 5---22................
MV change rate limiter 4---5...............
MV limiter 4---5..........................
MV lower limit 5---22.....................
MV monitor (cool) 5---8...................
M V m o n i t o r ( h e a t ) 5 --- 8...................
MV upper limit 5---22.....................
N
N a m e s o f p a r t s 1 --- 2......................
N o . 1 d i s p l a y 1 --- 3.........................
N o . 2 d i s p l a y 1 --- 3.........................
O
ON/OFF control 4---4.....................
Open/close hysteresis 5---23................
Operating Condition Restrictions 4---5......
Operating conditions 4---12, 4---13..........
Operation at start 4---7....................
Operation indicators 1---3.................
O p t i o n M o d e 1 --- 7 , 1 --- 9 , 5 --- 3 7.............
Option Unit Ratings and
Characteristics A---4...................
Other event input functions 4---10..........
Other functions 4---3......................
Outline 6---2.............................
Outline of the Communications
Function 6---2.........................
O u t p u t a s s i g n m e n t s 1 --- 5 , 3 --- 6.............
Output Unit
Ratings and Characteristics A---4.......
P
P a n e l c u t o u t 2 --- 5.........................
P arameter initialize 5 ---27.................
PARAMETER OPERATIONS LIST A---12..
P a r a m e t e r t y p e s 1 --- 7.....................
Parameters and Menus 1---7...............
PID / ON/OFF 5---33......................
PID Constant R efreshing Conditions A---15.
Platinum resistance thermometer 7---12....
Position---proportional control 4---3........
Position---proportional dead band 5---14.....
Position---proportional
t y p e 3 --- 7 , 3 --- 1 5 , A --- 7..................
Power supply 2---8........................
Precautions when wiring 2---8.............
P r e p a r a t i o n 7 --- 7 , 7 --- 9 , 7 --- 1 0..............
Preparations 7---4........................
Preparing for Communications 6---3........
P r o c e d u r e 2 --- 3 , 2 --- 4 , 6 --- 1 4................
Program Example 6---14...................
Program list 6---15........................
Proportional band 5---13..................
P r o t e c t M o d e 1 --- 7 , 1 --- 9 , 3 --- 1 2 , 5 --- 3........
P V d e a d b a n d 5 --- 4 3.......................
P V / S P 5 --- 6..............................
R
R a t i n g s A --- 2............................
Reading parameters 6---6..................
Reading/writing parameters 6---6...........
Registering calibration data 1---11..........
Relationship with set point limiter 4---11....
R e m o t e S P e n a b l e 5 --- 4 4...................
R e m o t e S P i n p u t 1 --- 4 , 2 --- 1 0...............
Remote SP input error 8---5...............
Remote SP lower limit 5---44...............
R e m o t e S P m o n i t o r 4 --- 1 2 , 5 --- 7............
Remote SP upper limit 5---44..............
R e m o t e / L o c a l 5 --- 1 9.......................
Response A---17..........................
Restrictions during SP ramp 4---7..........
RS---232C 1---10, 6---3.....................
R S --- 4 2 2 1 --- 1 0 , 6 --- 3.......................
R S --- 4 8 5 1 --- 1 0 , 6 --- 4.......................
RSP input error 3---6.....................
R u n / S t o p 4 --- 1 0 , 5 --- 9......................
RX (process val ue r ead)
command status A---19.................
S
S c a l i n g 3 --- 4 , 4 --- 1 1........................
Scaling lower limit 5---27..................
Scaling upper limit 5---27..................
S e c u r i t y 3 --- 1 2 , 5 --- 3.......................
Selecting modes 1---8......................
Selecting parameters 1---9.................
Selecting the Control Method 4---2..........
Sensor input 2---9.........................
Setpoint0 5---11.........................
Setpoint1 5---11.........................
Setpoint2 5---11.........................
Setpoint3 5---11.........................
Set p oint during SP ramp 5---8.............
Set p oint limiter 4---6.....................
Set point lower limit 5---33................