SICK CLV 480 - Page 207

Operating Instructions Chapter 10
CLV 480 Bar Code Scanner
8 010 080/O824/10-02-2005 © SICK AG · Division Auto Ident · Germany · All rights reserved 10-69
Appendix
E
Electrical installation.....................................................................5-1
EMC....................................................................................................9-2
Enclosure rating (IP).....................................................................9-2
Error messages
- Display in the Terminal Emulator......................................8-2
- Function .....................................................................................3-6
- List (CLV with external parameter memory) ................8-5
- List (CLV without external parameter memory)..........8-2
Error status in the reading result ............................................8-7
Ethernet ......................................................................................10-49
Evaluation
- Decoder types.........................................................................3-6
- Parameterization..................................................................6-23
F
Figures (overview)........................................................................I-13
Firmware.............................................................................................I-2
Focus position switching
- Function .....................................................................................3-7
- Parameterization.....................................................................6-9
- Trigger modes .........................................................................3-7
G
Glossary......................................................................................10-59
Good Read ...................................................................................6-27
H
Heating
- Behavior...............................................................................10-26
- Cables...................................................................................10-55
- Design...................................................................................10-26
- Electrical connection.......................................................10-27
- Function ...............................................................................10-26
- Power consumption.........................................................10-27
- Switching on delay ...........................................................10-26
- System requirements ...........................................................3-1
- Temperatur range............................................................10-26
Host interface
- Connecting.............................................................................5-15
- Data output string ...............................................................6-38
- Default setting ......................................................................5-15
- Function .....................................................................................3-6
- Max. cable lengths.................................................................5-9
- Monitoring in the Terminal Emulator............................6-37
- Parameterization..................................................................6-24
- Select hardware...................................................................5-16
I
I/O monitor in increment trigger...........................................6-31
Identical bar codes
- Function of CP, CW values..................................................4-6
- Minimum distance............................................................10-44
- Parameterizise the evaluation........................................6-23
- Separation.................................................................................4-6
IN 0 ... IN 4 switching inputs
- Assignment table.................................................................5-19
- Caracteristic data................................................................5-19
- Functions...................................................................................3-6
Incremental encoder
- Application.................................................................................3-2
- Electrical connecting.......................................................... 5-18
- Function..................................................................................... 3-8
- Installation ............................................................................. 4-11
Indicators ......................................................................................... 3-9
Installation
- Electrical installation .......................................................... 5-14
- Mounting ................................................................................... 4-7
- Overview...................................................................................... I-4
Intended use of CLV.................................................................... 2-1
Interbus-S.................................................................................. 10-49
Interfaces of CLV
- Functions................................................................................... 3-6
- Overview.................................................................................... 5-2
- Pin assignment ....................................................................... 5-7
L
Laser radiation
- Laser power............................................................................. 2-2
- Laser warning lables (content) ......................................... 2-2
- Protection class...................................................................... 2-2
- Protective circuits, internal ................................................. 2-3
- Replacing the laser warning labels.................................. 4-2
- User instructions .................................................................... 2-2
- Wave length............................................................................. 2-2
Laser timeout
- Function..................................................................................... 2-3
- Parameterization ................................................................. 6-23
LEDs
- Function (CLV with ext. param. memory)................... 3-11
- Function (CLV without ext. param. memory) ............ 3-10
- Parameterization Result 1 (LED "Read Result") ..... 6-24
- Position ...................................................................................... 3-5
Line scanner
- Dimensional drawing ............................................................ 9-3
- Function..................................................................................... 3-8
- Quick start ................................................................................ 6-3
- Technical data......................................................................... 9-1
M
Maintenance................................................................................... 7-2
Malfunctions
- Diagnosis and remedy......................................................... 8-9
- Error messages ...................................................................... 8-2
Master/slave (RS 232, RS 422/485)............................ 10-49
Messages (terminal interface) ............................................. 6-42
Method of operation
- Block diagram ......................................................................... 3-6
- Description ............................................................................... 3-6
Monitoring host interface
- Function.................................................................................. 6-37
- Starting the mode............................................................... 6-37
Mounting
- Accessories.............................................................................. 4-1
- Mounting the CLV .................................................................. 4-3
- Mounting the distance sensors..................................... 4-12
- Preparations ............................................................................ 4-1
- Reading pulse sensor ....................................................... 4-10
Mounting bracket
- Dimensioned drawings .................................................. 10-57