SICK CLV 480 - Page 208

10-70 © SICK AG · Division Auto Ident · Germany · All rights reserved 8 010 080/O824/10-02-2005
Chapter 10 Operating Instructions
CLV 480 Bar Code Scanner
Appendix
- Function..................................................................................... 4-3
N
No Read ........................................................................................ 6-27
O
One-Shot (oscillating mirror)
- Calculating parameter values for the CLV.............. 10-43
- Function.................................................................................. 6-12
Online help ................................................................................ 10-36
Operating
- Function of the LEDs ............................................................ 3-9
- With CLV-Setup.................................................................... 6-25
- With command strings................................................... 10-39
Operating data
- Display .................................................................................... 6-36
- Reset ....................................................................................... 6-36
Operating modes
- Adjusting mode.................................................................... 6-30
- I/O monitor in increment trigger.................................... 6-31
- Overview of modes ............................................................ 6-25
- Percentage evaluation ...................................................... 6-28
- Reading mode...................................................................... 6-25
- Show CP-limits ..................................................................... 6-30
Oscillating mirror
- Deflection ranges............................................................. 10-21
- Design........................................................................................ 3-5
- Dimensioned drawings ........................................................ 9-4
- Function..................................................................................... 3-8
- Function in adjusting mode............................................. 6-30
- Function in reading mode................................................ 6-25
- Function in show CP-limits............................................... 6-30
- Function in the percentage evalutation...................... 6-28
- Operating modes ................................................................ 6-10
- Parameterization ................................................................. 6-10
- Reversal points....................................................................... 3-8
- Technical data......................................................................... 9-2
- Troubleshooting................................................................... 8-17
P
Parameter memory, external
- Design.................................................................................. 10-22
- Electrical connection....................................................... 10-23
- Error messages...................................................................... 8-5
- Function............................................................................... 10-22
- LEDs......................................................................................... 3-10
- Mounting ............................................................................. 10-23
- Operating ............................................................................ 10-23
- Pin assignment ....................................................................... 5-8
- Replacing the CLV ........................................................... 10-25
- Saving parameters after download ................................ 6-6
- Startup first time .............................................................. 10-24
- Troubleshooting...................................................................... 8-3
- Wire colors ............................................................................ 5-11
Parameter set
- Download.................................................................................. 6-6
- Function..................................................................................... 6-5
- Upload........................................................................................ 6-5
Parameterization
- Calculating parameter values ..................................... 10-41
- CLV-Setup .................................................................................6-5
- Command strings.............................................................10-39
- Function .....................................................................................6-5
- Guide...........................................................................................6-9
- Replacing a CLV................................................................10-50
Percentage evaluation
- Function ..................................................................................6-28
- Function of "Read Result" LED ......................................3-10
- Read result output..............................................................6-29
- Start the mode.....................................................................6-28
Pin assignment of CLV ................................................................5-7
Pitch
- Definition....................................................................................4-5
- Limit values...............................................................................4-5
Power consumption .....................................................................2-4
Power-up delay
- Function .....................................................................................5-9
- Parametrization ....................................................................5-10
Product features............................................................................3-3
Profibus DP................................................................................10-49
Protection class .............................................................................9-2
Q
Quick start........................................................................................6-3
R
Reading diagnosis
- Function ..................................................................................6-36
- Starting the mode ...............................................................6-36
Reading distance
- Definition....................................................................................4-4
- Detection (external sensors).............................................3-7
Reading field diagrams ............................................................10-1
Reading field height
- line scanner...........................................................................10-3
- line scanner with osc. mirror........................................10-13
Reading mode
- Function ..................................................................................6-25
- Output of the reading result............................................6-25
- Troubleshooting ...................................................................8-10
Reading operation mode
- Start/stop mode.....................................................................3-7
- Tracking mode.........................................................................3-8
Reading pulse sensor
- Electrical connecting ..........................................................5-17
- Mounting.................................................................................4-10
- Parametrization for trigger source ................................4-11
Reading result
- Host interface.......................................................................6-37
- Terminal interface ...............................................................6-26
- Troubleshooting ...................................................................8-17
Reading trigger
- End of reading interval by IN 4..........................................3-2
- Function .....................................................................................3-6
- Parameterization..................................................................6-14
- Trigger modes .........................................................................3-6
- Triggering via Terminal Emulator ...................................6-26
- Troubleshooting ...................................................................8-10
Reading window