SICK CLV 480 - Page 209

Operating Instructions Chapter 10
CLV 480 Bar Code Scanner
8 010 080/O824/10-02-2005 © SICK AG · Division Auto Ident · Germany · All rights reserved 10-71
Appendix
- Cleaning .....................................................................................7-1
- Position.......................................................................................3-5
Repair .............................................................................................8-18
Replacing a CLV
- Via CLV-Setup....................................................................10-50
- Via the external parameter memory.........................10-51
Result 1 ... Result 4 switching outputs
- Caracteristic data................................................................5-21
- Connecting.............................................................................5-21
- Function .....................................................................................3-6
- Parameterization..................................................................6-24
S
Safety
- Authorized users.....................................................................2-1
- Enclosure rating/protection class ....................................9-2
- Features.....................................................................................3-3
- Intended use of CLV .............................................................2-1
- Laser radiation.........................................................................2-2
- Notes on device .....................................................................3-1
- Power supply.........................................................................5-10
- Silicone-based material .......................................................2-4
Scope of supply.............................................................................3-1
Self-test
- Error messages.......................................................................8-2
- Function ..................................................................................6-40
- Starting the mode ...............................................................6-40
Sensor for distance detection
- Electrical Connection .........................................................5-18
- Function ..................................................................................4-12
- Mounting.................................................................................4-12
Sensor switching input
- Caracteristic data................................................................5-17
- Connecting.............................................................................5-17
- Function .....................................................................................3-6
- Parameterization..................................................... 6-14, 6-24
Separation of bar codes
- CP value.....................................................................................4-6
- CW value....................................................................................4-6
- Minimum distance............................................................10-44
- Parameterization..................................................................6-23
Show CP-limits
- Function ..................................................................................6-30
- Starting the mode ...............................................................6-31
SICK Homepage (www)..............................................................1-1
SICK network (RS 485) ........................................................10-49
SICK Support ...............................................................................8-18
Skew
- Definition....................................................................................4-5
- Limit values...............................................................................4-5
SMART decoder.............................................................................3-6
Software versions ...........................................................................I-2
Specification diagrams.............................................................10-1
Splitter ............................................................................................6-38
Start/stop mode
- Function .....................................................................................3-7
- Parameterization..................................................................6-14
Start-up .............................................................................................6-3
Supply voltage ............................................................................... 5-9
- Connecting ............................................................................ 5-14
Surface reflection
- Avoiding reflection ................................................................. 4-5
Switching off the CLV ............................................................... 6-43
Symbols (typographical) ............................................................ 1-2
System messages
- Display in the terminal emulator ................................... 6-42
- Function..................................................................................... 3-6
- List of messages.............................................................. 10-28
System requirements
- CLV with heater ...................................................................... 3-3
- CLV without heater................................................................ 3-1
- Connection Modules ............................................................ 3-1
- Sensors ..................................................................................... 3-2
- Supply voltage......................................................................... 3-2
T
Tables (overview) ........................................................................I-10
Technical data................................................................................ 9-1
Terminal emulator ..................................................................... 6-26
Terminal interface
- Connecting ............................................................................ 5-16
- Data format........................................................................... 6-26
- Default setting...................................................................... 5-17
- Function..................................................................................... 3-6
- Max. cable length................................................................... 4-2
- Operating modes ................................................................ 6-36
Terminator.................................................................................... 6-38
Thread Blind hole
- Dimensions .............................................................................. 4-3
- Position ...................................................................................... 3-5
Tracking mode
- Function.................................................................................. 6-22
- Minimum gap........................................................................ 6-20
- Parameterization ................................................................. 6-21
Troubleshooting
- Analysis and remedy ............................................................ 8-9
- Error messages ...................................................................... 8-2
- Error status in the reading result ..................................... 8-7
U
Upload
- Functions................................................................................... 6-5
- Starting upload........................................................................ 6-5
V
Variants of CLV.............................................................................. 3-1
W
Warranty........................................................................................... 2-1
Windows........................................................................................... 3-2