Siemens SINUMERIK 828D Function Manual

Table of contents
Basic Functions
22 Function Manual, 09/2011, 6FC5397-0BP40-2BA0
13.2 Key data of the PLC-CPUs for 840D sl and 840Di sl............................................................... 839
13.3 Reserve resources (timers, counters, FC, FB, DB, I/O) .......................................................... 846
13.4 Startup hardware configuration of the PLC-CPUs................................................................... 847
13.5 Starting up the PLC program................................................................................................... 852
13.5.1 Installation of the basic program .............................................................................................. 852
13.5.2 Application of basic program ................................................................................................... 852
13.5.3 Version codes .......................................................................................................................... 853
13.5.4 Machine program ..................................................................................................................... 853
13.5.5 Data backup ............................................................................................................................ 854
13.5.6 PLC-series startup, PLC archive ............................................................................................. 854
13.5.7 Software upgrade .................................................................................................................... 856
13.5.8 I/O modules (FM, CP modules) ............................................................................................... 857
13.5.9 Troubleshooting ....................................................................................................................... 858
13.6 Coupling of the PLC CPUs ..................................................................................................... 859
13.6.1 General .................................................................................................................................... 859
13.6.2 Features of PLC CPUs ............................................................................................................ 859
13.6.3 Interface with integrated PLC .................................................................................................. 859
13.6.4 Diagnostic buffer on PLC ......................................................................................................... 861
13.7 Interface structure.................................................................................................................... 862
13.7.1 PLC/NCK interface .................................................................................................................. 862
13.7.2 Interface PLC/HMI ................................................................................................................... 868
13.7.3 PLC/MCP/HHU interface ......................................................................................................... 873
13.8 Structure and functions of the basic program.......................................................................... 875
13.8.1 Startup and synchronization of NCK PLC .............................................................................. 877
13.8.2 Cyclical mode (OB 1) ............................................................................................................... 877
13.8.3 Time-interrupt processing (OB 35) .......................................................................................... 879
13.8.4 Process interrupt processing (OB 40) ...................................................................................... 879
13.8.5 Diagnostic interrupt, module failure processing (OB 82, OB 86) ............................................. 880
13.8.6 Response to NCK failure ......................................................................................................... 880
13.8.7 Functions of the basic program called from the user program ................................................ 881
13.8.8 Symbolic programming of user program with interface DB ..................................................... 884
13.8.9 M decoding acc. to list ............................................................................................................. 886
13.8.10 PLC machine data .........................................
.......................................................................... 890
13.8.11 Configuration machine control panel, handheld unit, direct keys ............................................ 894
13.8.12 Switchover of machine control panel, handheld unit ............................................................... 902
13.9 SPL for Safety Integrated ........................................................................................................ 905
13.10 Assignment overview............................................................................................................... 906
13.10.1 Assignment: NCK/PLC interface .............................................................................................. 906
13.10.2 Assignment: FB/FC .................................................................................................................. 906
13.10.3 Assignment: DB ....................................................................................................................... 907
13.10.4 Assignment: Timers ................................................................................................................. 908
13.11 Memory requirements of the basic PLC program.................................................................... 909
13.12 Basic conditions and NC VAR selector.................................................................................... 912
13.12.1 Supplementary conditions ....................................................................................................... 912
13.12.1.1Programming and parameterizing tools ................................................................................... 912
13.12.1.2SIMATIC documentation required ........................................................................................... 913
13.12.1.3Relevant SINUMERIK documents ........................................................................................... 914

Siemens SINUMERIK 828D Specifications

General

Control Type	CNC
Operating System	Windows Embedded
Processor	Intel Atom
Display	10.4" color TFT display
Interfaces	Ethernet, USB
Programming	ShopMill, ShopTurn
Operation Panel Size	10.4"
Protection Class	IP65
PLC Memory	2 MB
Spindle Capacity	4 spindles
Hard Drive	CompactFlash