Siemens SINUMERIK 828D Function Manual

Basic Functions
Function Manual, 09/2011, 6FC5397-0BP40-2BA0
29
Table of contents
17.4.8 Feedrate for chamfer/rounding FRC, FRCM ......................................................................... 1404
17.4.9 Non-modal feedrate FB ......................................................................................................... 1405
17.4.10 Programmable singleaxis dynamic response ....................................................................... 1406
17.5 Supplementary conditions ..................................................................................................... 1411
17.5.1 General boundary conditions ................................................................................................. 1411
17.5.2 Supplementary conditions for feedrate programming ............................................................ 1411
17.6 Examples............................................................................................................................... 1413
17.6.1 Feedrate programming for chamfer/rounding FRC, FRCM ................................................... 1413
17.7 Data lists................................................................................................................................ 1415
17.7.1 Machine data ......................................................................................................................... 1415
17.7.1.1 NC-specific machine data ...................................................................................................... 1415
17.7.1.2 Channelspecific machine data ............................................................................................. 1415
17.7.1.3 Axis/Spindle-specific machine data ....................................................................................... 1416
17.7.2 Setting data ........................................................................................................................... 1416
17.7.2.1 Channelspecific setting data ................................................................................................ 1416
17.7.2.2 Axis/spindle-specific setting data ........................................................................................... 1416
17.7.3 Signals ................................................................................................................................... 1417
17.7.3.1 Signals to channel ................................................................................................................. 1417
17.7.3.2 Signals from channel ............................................................................................................. 1417
17.7.3.3 Signals to axis/spindle ........................................................................................................... 1417
17.7.3.4 Signals from axis/spindle ....................................................................................................... 1418
18 W1: Tool offset ......................................................................................................................................1419
18.1 Short description.................................................................................................................... 1419
18.2 Tool........................................................................................................................................ 1422
18.2.1 General .................................................................................................................................. 1422
18.2.2 Compensation memory structure .......................................................................................... 1424
18.2.3 Calculating the tool compensation ......................................................................................... 1426
18.2.4 Address extension for NC addresses T and M ...................................................................... 1426
18.2.5 Free assignment of D numbers ............................................................................................. 1428
18.2.6 Compensation block in case of error during tool change ...................................................... 1434
18.2.7 Definition of the effect of the tool parameters ........................................................................ 1437
18.3 Flat D number structure......................................................................................................... 1438
18.3.1 General .................................................................................................................................. 1438
18.3.2 Creating a new D number (compensation block) ...............
................................................... 1438
18.3.3 D number programming ......................................................................................................... 1439
18.3.4 Programming the T number ................................................................................................... 1441
18.3.5 Programming M6 ................................................................................................................... 1441
18.3.6 Program test .......................................................................................................................... 1442
18.3.7 Tool management or "Flat D numbers" ................................................................................. 1442
18.4 Tool cutting edge ................................................................................................................... 1444
18.4.1 General .................................................................................................................................. 1444
18.4.2 Tool parameter 1: Tool type .................................................................................................. 1446
18.4.3 Tool parameter 2: Cutting edge position ............................................................................... 1449
18.4.4 Tool parameters 3 - 5: Geometry - tool lengths ..................................................................... 1450
18.4.5 Tool parameters 6 - 11: Geometry - tool shape ..................................................................... 1452
18.4.6 Tool parameters 12 - 14: Wear - tool lengths ........................................................................ 1454
18.4.7 Tool parameters 15 - 20: Wear - tool shape .......................................................................... 1454
18.4.8 Tool parameters 21 - 23: Tool base dimension/adapter dimension ...................................... 1454

Siemens SINUMERIK 828D Specifications

General

Control Type	CNC
Operating System	Windows Embedded
Processor	Intel Atom
Display	10.4" color TFT display
Interfaces	Ethernet, USB
Programming	ShopMill, ShopTurn
Operation Panel Size	10.4"
Protection Class	IP65
PLC Memory	2 MB
Spindle Capacity	4 spindles
Hard Drive	CompactFlash