Siemens SINUMERIK 828D Function Manual

Table of contents
Basic Functions
28 Function Manual, 09/2011, 6FC5397-0BP40-2BA0
16.8.3 Spindle in setpoint range ....................................................................................................... 1342
16.8.4 Minimum / maximum speed of the gear stage ....................................................................... 1344
16.8.5 Diagnosis of spindle speed limitation ..................................................................................... 1345
16.8.6 Maximum spindle speed ........................................................................................................ 1347
16.8.7 Maximum encoder limit frequency .........................................................................................1348
16.8.8 End point monitoring .............................................................................................................. 1349
16.8.9 M40: Automatic gear stage selection for speeds outside the configured switching thresholds .....
1351
16.9 Spindle with SMI 24 (Weiss spindle) ..................................................................................... 1353
16.9.1 General Information ............................................................................................................... 1353
16.9.2 Sensor data ........................................................................................................................... 1353
16.9.3 Clamped state ........................................................................................................................ 1355
16.9.4 Additional drive parameters ................................................................................................... 1356
16.10 Examples............................................................................................................................... 1357
16.10.1 Automatic gear step selection (M40) ..................................................................................... 1357
16.11 Data lists................................................................................................................................ 1358
16.11.1 Machine data ......................................................................................................................... 1358
16.11.1.1NC-specific machine data ...................................................................................................... 1358
16.11.1.2Channelspecific machine data .............................................................................................. 1358
16.11.1.3Axis/spindlespecific machine data ........................................................................................ 1358
16.11.2 Setting data ........................................................................................................................... 1360
16.11.2.1Channelspecific setting data ................................................................................................. 1360
16.11.2.2Axis/spindle-specific setting data ........................................................................................... 1360
16.11.3 signals ................................................................................................................................... 1361
16.11.3.1Signals to axis/spindle ........................................................................................................... 1361
16.11.3.2Signals from axis/spindle ....................................................................................................... 1361
17 V1: Feedrates ........................................................................................................................................1363
17.1 Brief Description .................................................................................................................... 1363
17.2 Path feedrate F...................................................................................................................... 1366
17.2.1 General .................................................................................................................................. 1366
17.2.2 Type of feedrate G93, G94, G95 ........................................................................................... 1368
17.2.3 Type of feedrate G96, G961, G962, G97, G971 .................................................................... 1370
17.2.4 Feedrate with G33, G34, G35 (thread cutting) ............
.......................................................... 1374
17.2.4.1
General .................................................................................................................................. 1374
17.2.4.2 Programmable run-in and run-out path for G33, G34 and G35 ............................................. 1376
17.2.4.3 Linear progressive/degressive thread-lead change with G34 and G35 ................................. 1378
17.2.4.4 Stop for thread cutting ........................................................................................................... 1381
17.2.5 Feedrate for G331/G332, rigid tapping .................................................................................. 1385
17.2.6 Feedrate for G63, tapping with compensation chuck ............................................................ 1386
17.3 Feedrate FA for positioning axes........................................................................................... 1387
17.4 Feedrate control..................................................................................................................... 1389
17.4.1 General .................................................................................................................................. 1389
17.4.2 Feedrate disable and feedrate/spindle stop ........................................................................... 1390
17.4.3 Feedrate override on machine control panel ......................................................................... 1391
17.4.4 Programmable feedrate override ........................................................................................... 1395
17.4.5 Dry run feedrate ..................................................................................................................... 1396
17.4.6 Multiple feedrate values in one block ..................................................................................... 1398
17.4.7 Fixed feedrate values ............................................................................................................ 1402

Siemens SINUMERIK 828D Specifications

General

Control Type	CNC
Operating System	Windows Embedded
Processor	Intel Atom
Display	10.4" color TFT display
Interfaces	Ethernet, USB
Programming	ShopMill, ShopTurn
Operation Panel Size	10.4"
Protection Class	IP65
PLC Memory	2 MB
Spindle Capacity	4 spindles
Hard Drive	CompactFlash