Valtra 6550 - Page 1155

1098
Model Code Page
70. Frame and wheels
1. 1. 1994
6000--8750 720 4
15. 5. 1993
Tyre pressures and loadings/tyre (40 km/h)
Front axle Rear axle
Tyre Max. loading Pressure
Tyre Max. loading Pressure
11.00---16/8 1150 kg 250 kPa 13.6---38/8 1530 kg 200 kPa
12.4---24/8 1415 kg 230 kPa 13.6R38/8 1800 kg 160 kPa
12.4R24/8 1360 kg 160 kPa 14.9R38/8 2060 kg 160 kPa
13.6R24/8 1450 kg 160 kPa 16.9---34/8 1905 kg 170 kPa
13.6---24/8 1235 kg 200 kPa 16.9R34/8 2430 kg 160 kPa
13.6R28/8 1550 kg 160 kPa 16.9R38/8 2575 kg 160 kPa
14.9---24/8 1410 kg 180 kPa 18.4---34/8 2050 kg 140 kPa
14.9R24/8 1700 kg 160 kPa 18.4R34/8 2800 kg 160 kPa
14.9R28/8 1800 kg 160 kPa 18.4R38/8 3000 kg 160 kPa
14.9---28/8 1505 kg 180 kPa 18.4---38/8 2170 kg 140 kPa
16.9R28/8 2240 kg 160 kPa 20.8R38/8 3650 kg 160 kPa
480/65R24
1750 kg 160 kPa 540/65R38 2430 kg 160 kPa
/
1240 kg 70 kPa 1900 kg 70 kPa
480/65R28 1850 kg 160 kPa 600/65R34 2900 kg 140 kPa
1300 kg 70 kPa 2050 kg 70 kPa
540/65R28 2070 kg 120 kPa 600/65R38 3075 kg 160 kPa
1540 kg 60 kPa 2150 kg 70 kPa
17.5R24 2060 kg 160 kPa 620/75R30 3875 kg 160 kPa
19.5R24 2360 kg 160 kPa 650/65R38 3350 kg 120 kPa
12.4---24/12 IND. 2370 kg 380 kPa 2510 kg 60 kPa
14.9---24/12 IND. 3090 kg 330 kPa 16.9---34/14 IND. 3935 kg 290 kP a
13.6---24/10 FOR 1790 kg 250 kPa 18.4---34/14 IND. 4850 kg 290 kP a
14.9---24/14 FOR 2375 kg 300 kPa 18.4---34/14 FOR 2985 kg 260 kPa
14.9---28/14 FOR 2530 kg 300 kPa 18.4---38/14 FOR 3110 kg 260 kPa
16.9---24/14 IND 3530 kg 300 kPa 18.4---38/14 IND 5055 kg 290 kPa
With R---tyres at speed of 30 km/h the max permissible loading per tyre is 20 % bigger.
Adjusting track widths, front wheels and rear wheels
Adjusting front and rear wheel track widths is done in the same way.
Scotch the front wheels (or rear wheels) to prevent the tractor from moving. Raise the rear wheels off the ground and position
sturdy axle stands under the axle housing.
Track width can be adjusted by changing the posit ion of the wheel rim in relation to thecentral disc or by turning the wheel around
(as shown above). If tyres are turned move them to other side.
Make sure that the arrows on the upper part of the tyres are pointing forwards.
Lubricate the wheel nuts and tighten them to the recommended values (see technical specifications).