February 2013
7-23
ColorQube® 9303 Family
Wiring Data
Wiring Diagrams
Introduction
The main PWB connections are in the following wiring diagrams:
WD 1.1 Power Supply Unit (1 of 5) Figure 1
WD 1.2 Power Supply Unit (2 of 5) Figure 2
WD 1.3 Power Supply Unit (3 of 5) Figure 3
WD 1.4 Power Supply Unit (4 of 5) Figure 4
WD 1.5 Power Supply Unit (5 of 5) Figure 5
WD 1.6 Power Distribution PWB (1 of 2) Figure 6
WD 1.7 Power Distribution PWB (2 of 2) Figure 7
WD 3.1 Single Board Controller PWB (1 of 3) Figure 8
WD 3.2 Single Board Controller PWB (2 of 3) Figure 9
WD 3.3 Single Board Controller PWB (3 of 3) Figure 10
WD 5.1 DADH PWB (1 of 2) Figure 11
WD 5.2 DADH PWB (2 of 2) Figure 12
WD 6.1 Scanner PWB (1 of 3) Figure 13
WD 6.2 Scanner PWB (2 of 3) Figure 14
WD 6.3 Scanner PWB (3 of 3) Figure 15
WD 7.1 Tray 5 Control PWB (1 of 2) Figure 16
WD 7.2 Tray 5 Control PWB (2 of 2) Figure 17
WD 7.3 Tray 3 Module PWB (1 of 3) Figure 18
WD 7.4 Tray 3 Module PWB (2 of 3) Figure 19
WD 7.5 Tray 3 Module PWB (3 of 3) Figure 20
WD 8.1 Media Path Driver PWB (1 of 5) Figure 21
WD 8.2 Media Path Driver PWB (2 of 5) Figure 22
WD 8.3 Media Path Driver PWB (3 of 5) Figure 23
WD 8.4 Media Path Driver PWB (4 of 5) Figure 24
WD 8.5 Media Path Driver PWB (5 of 5) Figure 25
WD 8.6 Reg/Preheat IF PWB Figure 26
WD 9.1 Drum Driver PWB (1 of 4) Figure 27
WD 9.2 Drum Driver PWB (2 of 4) Figure 28
WD 9.3 Drum Driver PWB (3 of 4) Figure 29
WD 9.4 Drum Driver PWB (4 of 4) Figure 30
WD 9.5 IME Controller PWB (1 of 3) Figure 31
WD 9.6 IME Controller PWB (2 of 3) Figure 32
WD 9.7 IME Controller PWB (3 of 3) Figure 33
WD 9.8 Marking Unit Heater PWB Figure 34
WD 9.9 Marking Unit Driver PWB (1 of 4) Figure 35
WD 9.10 Marking Unit Driver PWB (2 of 4) Figure 36
WD 9.11 Marking Unit Driver PWB (3 of 4) Figure 37
WD 9.12 Marking Unit Driver PWB (4 of 4) Figure 38
WD 9.13 Quad Wave Amplifier PWB Figure 39
WD 9.14 Solenoid Patch PWB (1 of 3) Figure 40
WD 9.15 Solenoid Patch PWB (2 of 3) Figure 41
WD 9.16 Solenoid Patch PWB (3 of 3) Figure 42
WD 9.17 Ink Load Entry PWB (1 of 2) Figure 43
WD 9.18 Ink Load Entry PWB (2 of 2) Figure 44
WD 9.19 Cleaning Unit PWB Figure 45
WD 9.20 Printhead 1 PWB and Printhead 2 PWB Figure 46
WD 9.21 Printhead 3 PWB and Printhead 4 PWB Figure 47
WD 9.22 IOD Pre Amp PWB Figure 48
WD 12.1 LCSS PWB (1 of 5) Figure 49
WD 12.2 LCSS PWB (2 of 5) Figure 50
WD 12.3 LCSS PWB (3 of 5) Figure 51
WD 12.4 LCSS PWB (4 of 5) Figure 52
WD 12.5 LCSS PWB (5 of 5) Figure 53
WD 12.6 HVF PWB (1 of 11) Figure 54
WD 12.7 HVF PWB (2 of 11) Figure 55
WD 12.8 HVF PWB (3 of 11) Figure 56
WD 12.9 HVF PWB (4 of 11) Figure 57
WD 12.10 HVF PWB (5 of 11) Figure 58
WD 12.11 HVF PWB (6 of 11) Figure 59
WD 12.12 HVF PWB (7 of 11) Figure 60
WD 12.13 HVF PWB (8 of 11) Figure 61
WD 12.14 HVF PWB (9 of 11) Figure 62
WD 12.15 HVF PWB (10 of 11) Figure 63
WD 12.16 BM PWB (1 of 4) Figure 64
WD 12.17 BM PWB (2 of 4) Figure 65
WD 12.18 BM PWB (3 of 4) Figure 66
WD 12.19 BM PWB (4 of 4) Figure 67
WD 12.20 Tri Folder PWB Figure 68
WD 12.21 Inserter PWB (1 of 2) Figure 69
WD 12.22 Inserter PWB (2 of 2) Figure 70
WD 12.23 OCT PWB Figure 71
WD 12.24 HVF PWB (11 of 11) Figure 72
The diagrams have the following features:
• The connections on the PWB’s are in PJ numerical sequence where possible.
• The complete component to PWB wiring is shown. All interconnecting connectors are
shown, in part or in whole. Connectors shown in part have reference to other wiring dia
-
grams as necessary.
• The following colours are used to differentiate the voltages shown on the wiring diagrams:
– Purple = 0V.
– Green = +3.3V.
– Blue = +5V.
– Yellow = +12V.
– Black = +17V.
To Next Page
Loading...
Need help?
General
