Amazone AMATRON 3 - Mounting for ISOBUS Mode

148 pages

Save Page as PDF

To Next Page

To Previous Page

2.2

Mounting for ISOBUS mode

CMS-I-001583

For implements that are connected to an

ISOBUS tractor using the ISOBUS light cabling:

Disable the ISOBUS function of the tractor

terminal.

CMS-T-006370-A.1

2 | Installation instructions

Mounting for ISOBUS mode

MG5560-EN-II | E.1 | 21.04.2020

Main Page

Table of Contents3
About this Operating Manual7
Other Applicable Documents7
Validity7
Diagrams7
Notes7
Instructions8
Lists9
Item Numbers9
Orientation Paths10
Installation Instructions11
Basic Installation11
Mounting for ISOBUS Mode12
Mounting for AMABUS Mode13
Mounting for Parallel Operation14
AMATRON 3 Overview15
Front Side15
Rear Side16
Basic Operation17
Using the Toggle Button17
Using the F Keys18
Using the Directional Pad18
Entering Text18
Entering Numerical Values19
Using the Shift Key20
After Switching on21
Selecting the BUS Mode21
Checking the AUX-N Assignments22
Changing the AUX-N Assignments23
Main Menu Overview24
AMATRON 3 Configuration25
Entering the Basic Settings25
Enabling or Disabling Job Management25
Enabling or Disabling Ignition Switching25
Adjusting the Volume26
Setting the Brightness27
Setting the Date and Time28
Setting the Region and Language29
Configuring ISOBUS30
GPS Configuration31
Setting up the A100/A101 Receiver31
Setting up the AG-STAR Receiver31
Setting up the SMART6 Receiver33
Setting up Other GPS Receivers34
Setting up the ASD Interface34
Adjusting the Light Bar35
Configuring the Toggle Button35
Defining the Start Mode36
Configuring Parallel Operation36
Using AUX-N Input Devices37
Defining the AUX-N Assignment37
Defining the AUX-N Assignment Using the Functions List40
Defining the AUX-N Assignment Using the Input List41
Deleting the Selected AUX-N Assignment42
Confirm with "Yes42
The Assignment will be Deleted42
Deleting All AUX-N Assignments43
Using the Licence Management43
Select43
Confirm with "Yes43
The Assignment will be Deleted43
Using the Diagnostics45
Using USB Management45
Using the Pool Management46
Using the CAN Diagnosis46
Performing a Reset47
Configuring Implements48
Managing Implements48
Editing the Implement Data49
Editing the Implement Geometry Data50
Selecting the Implement51
Configuring Tractors53
Managing Tractors53
Editing the Tractor Data54
Editing the Tractor Geometry Data55
Configuring the Tractor Sensors57
Selecting the Tractor58
Using the Job Management59
Managing Jobs59
Editing Jobs61
Creating a New Job61
Adding Setpoints to a Job61
Adding a Worker to a Job64
Adding Implements and Tractors to a Job66
Checking the Map Type68
Searching for Jobs69
Copying Jobs69
Starting a Job70
Stopping a Job71
Exporting Jobs71
Using Master Data Management72
Managing Master Data72
Managing Setpoints73
Editing the Setpoints74
Managing Fields75
Editing the Field Data76
Managing the Customers76
Editing the Customer Data77
Managing Workers77
Editing Worker Data78
Managing Products78
Editing the Product Data79
Using the GPS Switch80
GPS Switch Overview80
GPS Switch Interface80
GPS Switch Functions83
GPS Quality Requirements85
Entering the Basic Settings for GPS Switch85
Defining the Implement Modelling85
Select the Source for the Driving Direction Detection86
Enabling the Acoustic Field Boundary Warning86
Defining the Map Display87
Defining the Map Alignment87
Entering the GPS Switch Settings for Spreaders88
Entering the GPS Switch Settings for Sprayers90
Entering the GPS Switch Settings for Seed Drills91
Setting the On/Off Point Delays93
Determining the Correction Times for On/Off Point Delays96
Checking the Switch-On and -Off Times97
Starting the GPS Switch98
Starting GPS Switch with Job Management98
Starting GPS Switch Without Job Management100
Zooming the Map101
Panning the Map102
Turning Around the Orientation of the Tractor Symbol102
Marking Obstacles103
Deleting an Obstacle Marking104
Creating the Field Boundary104
Deleting the Field Boundary105
Managing Virtual Headlands106
Creating Virtual Headlands106
Locking or Unlocking the Headlands108
Deleting the Headland108
Using Track Lines109
Selecting the Track Line Pattern109
Defining the Track Line Spacing111
Creating Beds111
Defining the Light Bar Sensitivity112
Creating Track Lines113
Using Part-Width Section Control115
Using Manual Part-Width Section Control115
Using Automatic Part-Width Section Control117
Managing Field Data123
Saving Recorded Field Data123
Deleting Recorded Field Data123
Loading Field Data from Recordings124
Defining the Radius for Field Detection127
Loading Field Data from a Shape File128
Configuring the Application Map130
Using the Driver Assistance System130
Calibrating the GPS Switch132
Correcting GPS Switch132
Correcting the GPS Drift with a Reference Point133
Correcting the GPS Drift Manually134
Using an External Light Bar135
Using the AUX-N Menu137
Eliminating Faults138
Take Screenshot141
Indexes142
Glossary142
Index144

Amazone AMATRON 3 - Mounting for ISOBUS Mode

Table of Contents

Other manuals for Amazone AMATRON 3

Related product manuals