Index
(continued)
3
—K—
Keyboard, 4-6
Korean Stereo, 5-40
—L—
Label Channel Identifier, 5-23
Labeling, 7-17
LCI, 5-23
LEVEL
key, 4-7, 4-18
Level range, 6-23
LF bandwidth, 5-39
Line 21 Data Service, 5-32, 5-33
Line connector, 1-10
Line frequency, 7-22
LINE SYNC, 7-4
Line voltage, 7-22
Listener function, 6-6
Local lock out, 6-6, 6-12
Local time offset, 6-39
Luminance, 7-4, 7-7, 7-19
Luminance level selection, 4-34
Luminance signal amplitude, 7-19
—M—
Main channel, 7-10, 7-15
Main menu, 3-4, 4-3
Maintenance, 1-9
Manual settings, 4-9
Memory registers, 4-35
Message communication functions, 6-3
Message Terminator, 6-13
Modulation, 7-5, 7-6, 7-12, 7-13, 7-15
Modulation frequency setting, 3-11
Modulation matrix, 7-12, 7-13
Mono carrier, 7-10
Mosaic graphics, 5-9
Moving Block, 4-67, 5-16, 7-9
MTBF, 7-21
MTS input, 5-52, 5-62, 5-63
MTS Multiplex, 7-11
MTS multiplex input, 3-18
Multi Labelling, 5-22, 5-23
Multiburst, 4-48, 7-8, 7-9
—N—
NICAM amplitude, 6-34
NICAM Clock, 7-11
NICAM data, 5-46, 5-47, 7-11
NICAM de-emphasis, 5-46
NICAM output, 5-46, 7-11
NICAM sound, 5-44, 5-61, 7-11
NICAM source, 6-35
NICAM Test Modes, 5-46
NICAM test signal, 5-46
NICAM-728, 5-42
Nominal line frequency, 1-10
Nominal voltage range, 1-10
Numerical input, 4-15, 4-18, 4-22, 4-26
Numerical keypad, 4-7
—O—
Operating position, 1-11
Out of Range message.
See
Error message
Output of NICAM sound, 3-18
Overscan indication, 7-8
—P—
Page Header Control Bits, 5-9, 5-13
Page update, 5-9
PAL, function verification,, 8-5
Parity, 6-11
Parity check, 7-20
Pattern combinations, 4-31, 7-9
PATTERN
keys, 4-6, 4-30
Pattern parameter, 3-11
Pattern parameter selection, 4-31
Pattern selection, 4-30
Patterns, 7-8
PDC, 4-14, 6-36
PDC Data Set, 5-23
PDC description, 5-22
PDC memory location, 5-8
PDC Preselection data, 5-7
PDC Program Title, 5-24
PDC test data, 5-8
PDC, function verification, 8-12, 8-29
Performance Characteristics, 7-3
Phase tolerance, 7-8
PIL, 5-24, 5-30
Pilot carrier, 5-48
Pilot carrier frequency, 7-13
Pilot signal, 7-11
Pilot subcarrier, 7-15
PLUGE, 4-56, 7-8, 7-9
Polarity, 7-4, 7-6, 7-19
Power cable, 1-10, 7-23
Power consumption, 7-22
Power Requirements, 7-22
Power switch, 3-13
Pre-defined country list, 3-5, 4-7
Pre-emphasis (FM), 6-34, 7-12
Preselection Function, 5-7, 5-22, 5-23
Program message, 6-21
Program Message Syntax, 6-13
Programme Delivery Control, 5-22
Programme Identification Label.
See
PIL
Programming examples, 6-43
Progressive Scan Check, 4-67, 4-68, 5-16, 7-9
Protective earth conductor, 1-9
PSF, 5-7, 5-23
Purity, 4-55, 7-8
To Next Page