Huawei Quidway S5700 Series - Page 142

<Quidway> system-view
[Quidway] sysname Member-1
[Member-1] vlan 10
[Member-1-vlan10] quit
[Member-1] interface gigabitethernet 0/0/1
[Member-1-GigabitEthernet0/0/1] port link-type trunk
[Member-1-GigabitEthernet0/0/1] port trunk allow-pass vlan 10
[Member-1-GigabitEthernet0/0/1] quit
[Member-1] interface gigabitethernet 0/0/2
[Member-1-GigabitEthernet0/0/2] port link-type trunk
[Member-1-GigabitEthernet0/0/2] port trunk allow-pass vlan 10
[Member-1-GigabitEthernet0/0/2] quit
[Member-1] interface vlanif 10
[Member-1-Vlanif10] quit
# Configure member switch 2.
<Quidway> system-view
[Quidway] sysname Member-2
[Member-2] vlan 10
[Member-2-vlan10] quit
[Member-2] interface gigabitethernet 0/0/1
[Member-2-GigabitEthernet0/0/1] port link-type trunk
[Member-2-GigabitEthernet0/0/1] port trunk allow-pass vlan 10
[Member-2-GigabitEthernet0/0/1] quit
[Member-2] interface vlanif 10
[Member-2-Vlanif10] quit
# Configure member switch 3.
<Quidway> system-view
[Quidway] sysname Member-3
[Member-3] vlan 10
[Member-3-vlan10] quit
[Member-3] interface gigabitethernet 0/0/1
[Member-3-GigabitEthernet0/0/1] port link-type trunk
[Member-3-GigabitEthernet0/0/1] port trunk allow-pass vlan 10
[Member-3-GigabitEthernet0/0/1] quit
[Member-3] interface vlanif 10
[Member-3-Vlanif10] quit
Step 2 Configure NDP.
# On switches, enable NDP in the system view and on an interface.
# Configure the administrator switch.
[Administrator-1] ndp enable
[Administrator-1] interface gigabitethernet 0/0/1
[Administrator-1-GigabitEthernet0/0/1] ndp enable
[Administrator-1-GigabitEthernet0/0/1] quit
[Administrator-1] interface gigabitethernet 0/0/2
[Administrator-1-GigabitEthernet0/0/2] ndp enable
[Administrator-1-GigabitEthernet0/0/2] quit
# Configure member switch 1.
[Member-1] ndp enable
[Member-1] interface gigabitethernet 0/0/1
[Member-1-GigabitEthernet0/0/1] ndp enable
[Member-1-GigabitEthernet0/0/1] quit
[Member-1] interface gigabitethernet 0/0/2
[Member-1-GigabitEthernet0/0/2] ndp enable
[Member-1-GigabitEthernet0/0/2] quit
# Configure member switch 2.
[Member-2] ndp enable
[Member-2] interface gigabitethernet 0/0/1
[Member-2-GigabitEthernet0/0/1] ndp enable
Quidway S5700 Series Ethernet Switches
Configuration Guide - Network Management 3 HGMP Configuration
Issue 01 (2011-10-26) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
131