JBL SDP-75 - Page 157

157 pages

Save Page as PDF

To Previous Page

To Previous Page

Loading...

156

Table of Contents

Notices5
Important Safety Instructions6
Table of Contents7
1 Introduction11
- About this Guide12
- Product Information14
- System Integration15
- Jbl Synthesis Certified Installers15
- Unpacking the Sdp-7516
- The Hardware17
- The Software20
2 Network Setup29
- Choosing a Network Configuration29
- Connecting to the Sdp-7530
- Changing the Network Settings through the Front Panel42
- Changing the Wi-Fi Settings through the Gui44
- Changing the Ethernet Settings through the Gui47
- About Vnc and Zero-Conf Networking49
  - About VNC (Virtual Network Computing)49
  - About Zero-Configuration Networking49
3 Network Streaming50
- The up N P Protocole50
- Upnp Network Architecture50
- Recommended Upnp Software51
4 Daily Operations53
- Available User Interfaces53
- Using the Front Panel54
- Using the Ir Remote Control57
- Using the Graphical Interface59
5 Basic Settings61
- Naming Your Sources61
- Configuring Your Sources62
- Default Source Configuration64
- Level and Delay Alignment Options65
- Naming, Saving and Loading Presets66
- Default Preset67
- Set a Maximum Volume68
- Set the DIM Level69
- Backup/Restore of Presets69
6 Overview of the Setup Procedure71
7 Essential Tools and Settings72
- Audio Clock Settings72
  - Audio Clock Status Information72
  - Audio Clock Setup73
- Metering the Inputs and Outputs74
- Playing Pink Noise on the Speakers75
- Solo/Mute an Input or an Output76
- Viewing the Acoustical Graphs78
8 Specify the Speaker Layout82
- Overview of the Speakers Setup Procedure82
- Introducing the Speaker/Room Setup Tool82
- An Example of a Specific Speaker Layout84
- Available Initial Layouts85
- Select an Initial Speaker Layout86
- Adding Speakers87
  - Adding Regular Speakers87
  - Adding Dolby Enabled Upfiring Speakers88
- Removing Speakers89
- Configure the Settings of each Speaker89
- Configure the Crossover Settings (Optional)91
- Mapping the Channels of Different Formats91
- Send Pink Noise to Verify the Routing of the Speakers92
- Save the Preset93
9 Specify an Array of Speakers94
- Setting up an Array of Speakers94
- Example of an Array of Speakers95
- Adjust the Gain95
- Save the Preset96
10 Decoder / Up-Mixer Settings97
- Supported Decoders/Up-Mixers97
- Listening Formats98
- Using the Front Panel102
  - Listening Format Selection102
  - Decoders Configuration102
- Using the Graphical Interface103
  - Listening Formats Selection103
  - Decoders Configuration103
- Decoders Settings104
11 Getting Ready for Calibration108
- Very Important Tips108
- Checklist before You Start108
- Important Recommendations for Microphone Placement109
12 Calibrate the Active Crossovers (Optional)111
- Overview of the Crossover Setup Procedure111
- Configure the Advanced Settings (Optional)112
- Adjust the Master Output Level114
- Calibrate the Active Crossovers115
- Verify the Sound of the Calibrated Crossovers116
  - Visualize the Acoustical Graphs for each Speaker116
  - Listen to each Speaker Connected to the Crossover118
- Save the Preset118
13 Level and Delay Calibration119
- Overview of the Calibration Procedure119
- Adjust the Master Output Level119
- Normal Calibration Sequence120
- Common Problems During Calibration121
- Calibration Status121
- Checking the Speaker Summary after Calibration122
- Multi-Point Measurements (Optional)125
- Compute the Optimization Filters125
- Save the Preset126
14 Setup Bass Management127
- Overview of the Bass Management Setup Procedure127
- Fully Customizable Bass Management128
- Bass Management Mode129
- Quick Setup Menu131
  - Set Filters132
  - Apply to Selected Speakers132
- Bass Management Settings for Individual Speaker133
- Lfe & Misc134
15 Setup Target Curves136
- Overview of this Procedure136
- Setting up One or more Target Curves136
16 Verify the Sound of Your Optimized Speaker System138
- Visualize the Acoustical Graphs for All Speakers138
- Listen to the System139
17 Fine Tuning Optimization Settings140
- Main Optimization Settings140
- Target Curve142
- Limiter Curve142
- Advanced Optimization Settings143
18 Performing Multi-Point Measurements146
- Relevant Measurement Positions147
- Multi-Point Calibration Procedure148
- Weighting Multiple Measurements148
19 Appendix149
- Insert an External Stereo Dac149
- Remote Start and Stop149
- Automation149
- Signal Flow of the Sdp-75150
  - Setup Process and Filters Calculation150
- Speaker Placement Recommendations150
- Db25 Connector: Analog Pinout Pinout151
- Db25 Connector : Aes Pinout151
- Measurement Microphone152

Related product manuals

Preview: JBL S3100

Preview: JBL SB130

Preview: JBL SUB300

Preview: JBL SCS 178

Preview: JBL SCS 140

Preview: JBL SCS 260.5

Preview: JBL CINEMA SB100

JBL CINEMA SB100

Preview: JBL CINEMA SB250

JBL CINEMA SB250