JBL SDP-75 - Available Initial Layouts

84
8.4 AVAILABLE INITIAL LAYOUTS
The following layout templates are available to start your setup process with an initial layout as similar as possible to
your specific configuration.
NOTE: For detailed information about speaker recommendations, please refer to the appendix of this
document and to the related Dolby, DTS and Auro-3D recommendations.
STEREO AND SURROUND LAYOUTS
DOLBY ATMOS LAYOUTS
• Stereo 2.0 (L/R)
• 5.1 (L/R/C/LFE/Ls/Rs)
• 7.1 (L/R/C/LFE/Ls/Rs/Lrs/Rrs)
• Dolby Atmos - 5.1.2 (5.1 + Ltm/Rtm)
• Dolby Atmos - 5.1.4 (5.1 + Ltf/Rtf + Ltr/Rtr)
• Dolby Atmos - 7.1.2 (7.1 + Ltm/Rtm)
• Dolby Atmos - 7.1.4 (7.1 + Ltf/Rtf + Ltr/Rtr)
• Dolby Atmos - 9.1.2 (7.1 + Lw/Rw + Ltm/Trm)
• Dolby Atmos - 9.1.4 (7.1 + Lw/Rw + Ltf/Rtf +
Ltr/Rtr)
AURO-3D LAYOUTS
DTS:X LAYOUTS
• Auro-3D - 9.1 (5.1 + HL/HR + HLs/HRs)
• Auro-3D - 10.1 (5.1 + HL/HR + HLs/HRs + T)
• Auro-3D - 11.1 (5.1 + HL/HR + HC + HLs/HRs + T)
• Auro-3D - 11.1 (7+4) (7.1 + HL/HR + HLs/HRs)
• Auro-3D - 13.1 (7.1 + HL/HR + HC + HLs/HRs + T)
• DTS:X - 5.1.2 (5.1 + Lh/Rh)
• DTS:X - 5.1.4 (5.1 + Lh/Rh + Lhr/Rhr)
• DTS:X - 7.1.2 (7.1 + Lh/Rh)
• DTS:X - 7.1.4 Heights (7.1 + Lh/Rh + Lhr/Rhr)
• DTS:X - 7.1.4 Tops (7.1 + Ltf/Rtf + Ltr/Rtr)
STANDARD LAYOUT
In addition to the Dolby, DTS and Auro3D templates, the SDP-75 includes a set of standard layouts. These
layouts are based on a 7.1 surround layout with additional speakers to support multiple surround and 3D
formats such as Dolby Atmos, DTS:X and Auro-3D.
Note that this layout can be modified to support the largest Dolby Atmos configuration.
• The 16 speaker layout : Standard 9.1.6 (7.1 + Lw/Rw + Ltf/Rtf + Ltr/Rtr + Hc + T)
• 8 speakers (7 full-range speakers + 1 subwoofer) for the 7.1 surround layout
• 6 speakers based on the Dolby Atmos format:
• 2 additional surround speakers: Lw & Rw (Left wide & Right wide)
• 4 additional height speakers: Ltf & Rtf (Left & Right top front) and Ltr & Rtr (Left & Right top rear)
• 1 additional center height speaker for the Center Top Front channel: HC (Auro-3D ) or Ch (DTS:X)
• 1 additional ceiling speaker for the Top channel: T (Auro-3D ) or Oh (DTS:X).
• The 20 speakers layout : Standard 11.1.8 (7.1 + Lw/Rw + Ltf/Rtf + Ltr/Rtr + Hc + T + Ltm/Rtm + Lc/Rc)
• based on the 9.1.6 layout
• 2 additional Top Middle channels : Ltm/Rtm used by Dolby Atmos and DTS:X formats
• 2 additional speakers behind the screen: Lc/Rc used by Dolby Atmos and DTS:X formats.
• The 32 speakers layout : Standard 21.1.10 (7.1 + Lw/Rw + Ltf/Rtf + Ltr/Rtr + Hc + T + Ltm/Rtm + Lc/Rc
+ Lsc/Rsc + Ls1/Rs1 + Ls2/Rs2 + Lrs1/Rrs1 + Lcs/Rcs)
• based on the 11.1.8 layout
• 2 additional speakers behind the screen : Lsc/Rsc used by the Dolby Atmos format
• 4 additional surround speakers : Ls1/Rs1 and Ls2/Rs2 used by Dolby Atmos and DTS:X formats
• 2 addition rear surround speakers Lrs1/Rrs1 used by the Dolby Atmos format
• 2 additional center surround speakers: Lcs/Rcs used by the Dolby Atmos format.