Juniper EX4200 User Manual

Table 43: Software Support for SFP+ Passive Direct Attach Cables for EX Series
Switches (continued)
Cable LengthSoftware Support AddedSwitch
1 m (3 ft) and 3 m (10 ft)Junos OS Release 13.2X51-D15EX4300-32F switches
1 m (3 ft), 3 m (10 ft), 5 m (16 ft), and 7 m
(23 ft)
Junos OS Release 13.2X51-D26EX4300-24T-S, EX4300-24P-S,
EX4300-48T-S,and EX4300-48P-S switches
1 m (3 ft) and 3 m (10 ft)Junos OS Release 13.2X51-D26EX4300-32F-S switches
1 m (3 ft), 3 m (10 ft), and 7 m (23 ft)Junos OS Release 10.2EX4500 switches
5 m (16 ft)Junos OS Release 11.2
1 m (3 ft), 3 m (10 ft), 5 m (16 ft), and 7 m
(23 ft)
Junos OS Release 12.2EX4550-32T-AFI, EX4550-32T-AFO,
EX4550-32T-DC-AFI, EX4550-32T-DC-AFO,
EX4550-32F-AFI, EX4550-32F-AFO,
EX4550-32F-DC-AFI, and
EX4550-32F-DC-AFO switches
1 m (3 ft), 3 m (10 ft), 5 m (16 ft), and 7 m
(23 ft)
Junos OS Release 12.3R5EX4550-32F-S switches
1 m (3 ft), 3 m (10 ft), and 7 m (23 ft)Junos OS Release 10.0EX8200 8-port SFP+ line cards (EX8200-8XS)
5 m (16 ft)Junos OS Release 10.3
1 m (3 ft), 3 m (10 ft), and 7 m (23 ft)Junos OS Release 10.3EX8200 40-port SFP+ line cards
(EX8200-40XS)
5 m (16 ft)Junos OS Release 11.1
NOTE: We recommendthat you use only SFP+ direct attachcables purchased
from Juniper Networks with your Juniper Networks device.
CAUTION: If you are having a problem running a Juniper Networks device
that is using a third-party optic or cable, the Juniper Networks Technical
Assistance Center (JTAC) can help you diagnose the source of the problem.
Your JTAC engineer might recommend that you check the third-party optic
or cable and potentially replace it with an equivalent Juniper Networks optic
or cable that is qualified for the device.
The cables are hot-removable and hot-insertable: You can remove and replace them
without powering off the switch or disrupting switch functions. A cable comprises a
low-voltage cable assembly that connects directly into two SFP+ ports, one at each end
of the cable. The cables use high-performance integrated duplex serial data links for
bidirectional communication and are designed for data rates of up to 10 Gbps.
119Copyright © 2015, Juniper Networks, Inc.
Chapter 8: Transceiver and Cable Specifications

Juniper EX4200 Specifications

General

Model	EX4200
Switching Capacity	128 Gbps
Layer	Layer 2 and Layer 3
Form Factor	1U
Throughput	96 Mpps
Maximum VLANs	4096
MAC Address Table Size	16, 000
DRAM	1 GB
Flash Memory	1 GB
Forwarding Rate	96 Mpps
JUNOS Software	Yes
Ports	24 or 48
Stacking	Up to 10 switches in a Virtual Chassis configuration
Power Supply	AC or DC
Management	CLI, SNMP, J-Web
Input Voltage	100-240 VAC or -48 VDC
Operating Temperature	0°C to 45°C
Redundancy	Redundant power supplies
Virtual Chassis Technology	Yes
Storage Temperature	-40°C to 70°C
Humidity	5% to 90% non-condensing