Lenze i410 - Page 254

Display code Short designaon Default seng Seng range Address Category
└ P151.01 Operang
me x s - (Read only) 0x2D81:001 general
└ P151.02 Power-on me x s - (Read only) 0x2D81:002 general
└ P151.03 CU oper. me x ns - (Read only) 0x2D81:003 general
└ P151.04 Switching cycles - - (Read only) 0x2D81:004 general
└ P151.05 Relay cycles - - (Read only) 0x2D81:005 general
└ P151.06 Short-circ.count - - (Read only) 0x2D81:006 general
└ P151.07 Earthfault count - - (Read only) 0x2D81:007 general
└ P151.08 Clamp acve - - (Read only) 0x2D81:008 general
└ P151.09 Fan oper. me x s - (Read only) 0x2D81:009 general
P155.xx Fault memory
P155.00 Error memory - - (Read only) 0x2006:000 general
P190.xx Device data
└ P190.01 Product code - - (Read only) 0x2000:001 general
└ P190.02 Serial number - - (Read only) 0x2000:002 general
└ P190.04 CU rmware ver. - - (Read only) 0x2000:004 general
└ P190.05 CU rmware type - - (Read only) 0x2000:005 general
└ P190.06 CU bootlder ver. - - (Read only) 0x2000:006 general
└ P190.07 CU bootlder type - - (Read only) 0x2000:007 general
└ P190.08 OBD version - - (Read only) 0x2000:008 general
└ P190.10 PU rmware ver. - - (Read only) 0x2000:010 general
└ P190.11 PU rmware type - - (Read only) 0x2000:011 general
└ P190.12 PU bootlder ver. - - (Read only) 0x2000:012 general
└ P190.13 PU bootlder type - - (Read only) 0x2000:013 general
└ P190.14 Mod. rmware - - (Read only) 0x2000:014 general
└ P190.15 Com. FW rev no. - - (Read only) 0x2000:015 general
└ P190.16 ComBootlderRevNo - - (Read only) 0x2000:016 general
└ P190.17 CU FW subtype - - (Read only) 0x2000:017 general
P191.00 Device name "My De
vice" Text 0x2001 general
P192.xx Device module
└ P192.04 CU type code - - (Read only) 0x2002:004 general
└ P192.05 PU type code - - (Read only) 0x2002:005 general
└ P192.06 CU serial number - - (Read only) 0x2002:006 general
└ P192.07 PU serial number - - (Read only) 0x2002:007 general
P198.00 Status load. par - - (Read only) 0x2827 general
P200.00 Control select. Flexible I/O [0] Selecon list 0x2824 general
P201.xx Stnd. setpoints
└ P201.01 Freq. setp. src. Analog input 1 [2] Selecon list 0x2860:001 general
└ P201.02 PID setp. src. Keypad [1] Selecon list 0x2860:002 general
└ P201.03 Torque setp.src. Analog input 1 [2] Selecon list 0x2860:003 general
P202.xx Keypad setpoints
└ P202.01 KP freq.setpoint 20.0 Hz 0.0 ... 599.0 Hz 0x2601:001 general
└ P202.02 KP PID setpoint 0.00 PID unit -300.00 ... 300.00 PID unit 0x2601:002 general
└ P202.03 Torque setp. 100.0 % -400.0 ... 400.0 % 0x2601:003 general
P203.xx Start/stop confg
└ P203.01 Start method Normal [0] Selecon list 0x2838:001 general
└ P203.02 Start at powerup O [0] Selecon list 0x2838:002 general
└ P203.03 Stop method Standard ramp [1] Selecon list 0x2838:003 general
P208.xx Mains sengs
└ P208.01 Mains voltage 230
Ve [0] Selecon list 0x2540:001 general
└ P208.02 LU warn. thresh. 0 V * 0 ... 800 V 0x2540:002 general
└ P208.03 LU error thresh. x V - (Read only) 0x2540:003 general
└ P208.04 LU reset thresh. x V - (Read only) 0x2540:004 general
└ P208.05 OU warn. thresh. 0 V * 0 ... 800 V 0x2540:005 general
└ P208.06 OU error thresh. x V - (Read only) 0x2540:006 general
* Default seng dependent on the model.
Using accessories
K
eypad
Keypad parameterisaon mode
254