What to do if Lexmark MS711 Printer displays 'Change [paper source] to [custom string] load [orientation]'?
If your Lexmark printer displays a 'Change [paper source]' message, load the correct size and type of paper in the tray, and then press on the printer control panel. You can also cancel the print job.
What to do if Lexmark MS711 says 'Defective flash detected'?
If your Lexmark printer displays a 'Defective flash detected' message, you can replace the defective flash memory card. Alternatively, you can press on the printer control panel to ignore the message and continue printing, or cancel the current print job.
What to do if my Lexmark Printer says 'Memory full'?
If your Lexmark Printer displays a 'Memory full' message, you can try the following: First, press on the printer control panel to clear the message. If the problem persists, decrease the resolution setting or install additional printer memory.
How to fix 'Incorrect paper size, open [paper source]' on Lexmark Printer?
If your Lexmark printer displays an 'Incorrect paper size' message, try these steps: Load the correct size of paper in the tray. You can also press on the printer control panel to clear the message and print using a different tray. Check the tray length and width guides to ensure the paper is loaded properly. Also, verify that the correct paper size and type are specified in Print Properties, the Print dialog, or the Paper menu on the printer control panel. If the MP Feeder Size is set to Universal, ensure the paper is large enough for the data being printed. As a last resort, cancel the print job.
What to do if Lexmark Printer displays 'Load staples'?
If your Lexmark printer is showing a 'Load staples' message, you should replace or insert the specified staple cartridge in the finisher. Alternatively, you can press on the printer control panel to clear the message and continue printing, or cancel the print job.
What to do if Lexmark MS711 says 'Check tray [x] connection'?
If your Lexmark printer displays a 'Check tray connection' message, try turning the printer off and then back on. If the error persists, turn off the printer, unplug the power cord, remove the specified tray, reattach it, reconnect the power cord, and then turn the printer back on. If the error occurs again, repeat the above steps and then contact customer support. You can also press on the printer control panel to clear the message and continue printing.
What to do if my Lexmark Printer says 'Cartridge low'?
If your Lexmark printer indicates that the cartridge is low, you may need to order a new toner cartridge. You can press on the printer control panel to clear the message and continue printing if necessary.
Why does my Lexmark Printer say 'Close door or insert cartridge'?
The 'Close door or insert cartridge' message on your Lexmark printer means the toner cartridge is either missing or not installed properly. To resolve this, insert the cartridge and then close all doors and covers.
What to do if Lexmark Printer displays 'Disk full'?
If your Lexmark printer displays a 'Disk full' message, you can delete fonts, macros, and other data stored on the printer's hard disk. Alternatively, you can install a printer hard disk with a larger capacity.
How to resolve 'Complex page, some data may not have printed' on Lexmark Printer?
If your Lexmark printer displays the message 'Complex page, some data may not have printed', you can press on the printer control panel to clear the message and continue printing. Alternatively, reduce the number and size of fonts, the number and complexity of images, and the number of pages in the print job. You could also cancel the print job or install additional printer memory.
General| Print Resolution | 1200 x 1200 dpi |
|---|---|
| Operating Systems Supported | Windows, macOS, Linux |
| Print Technology | Laser |
| Processor Speed | 800 MHz |
| Standard Memory | 512 MB |
| Maximum Memory | 1.5 GB |
| Output Capacity | 250 sheets |
| Hard Drive | Optional |
| Energy Star Certified | Yes |
| Printer Type | Monochrome Laser |
| Connectivity | USB, Ethernet |
| Duplex Printing | Automatic |
| Print Languages | PostScript 3 |
| Dimensions (W x D x H) | 15.7 x 17.5 x 15.7 inches |
To Next Page
