MG MGB - Hazard warning flasher unit and audible warning buzzer

THE ELECTRICAL
SYSTEM
Section
Na.2
WINDSHIELD
WASHER
MOTOR
Removing
(1) Disconnect
the battery.
(2)
Disconnect the
wiring from the
motor
terminals.
(3)
Disconnect the
water
tubes.
(4)
Unscrew
the
two
pump
mounting
screws
and
re-
move
the
pump
assembly.
Re■tting
(5)
Reverse
the
removing
procedure in
(l)
to
(4).
Section
Na.3
LAMPS
Front
and
rear
side-marker lamps
(1)
Disconnect
the battery.
(2)
Remove
the
two
nuts
and four washers
securing
the
lamp.
('3)
Partially
remove
.the lamp
and
disconnect
the
electrical leads
at
the harness
connectors.
Number-plate
lamp
(1)
Disconnect
the battery.
(2)
Remove
the
two
nuts
and washers
retaining the
lamps
to
the
lamp
bracket;
alternatively,
remove
the lamp
complete
with the
bracket.
(3) Disconnect the
electrical leads
at
the harness
connections,
and
remove
the lamp.
Section
Na.4
HAZARD WARNING
FLASHER UNIT AND
AUDIBLE
WARNING
BUZZER
Removing
Hazard
warning
■asher
unit
(1)
Disconnect the battery.
(2)
Remove
the
centre
console—Section
R.34.
(3)
Withdraw
the ■asher
unit from its
retaining clip.
(4) Disconnect the
wiring
plug
from the ■asher
unit.
Audible
warning
buzzer
(5)
Disconnect the battery.
(6)
Remove
the
centre
console—Section
R.34.
(7)
Remove
the
screw or
nut'
retaining the buzzer.
(8)
Disconnect
the
wiring from the buzzer.
Re■tting
Hazard
warning
■asher
unit
(9)
Reverse
the
removing
procedure in
(l)
to
(4).
MGB.
Issue
4.
85699
2NC696A
Fig. Na.2
The
centre
console
removed showing:
1.
The hazard
warning
3.
Later
type
warning
■asherunit buzzer.
2.
Early
type
warning
buzzer.
Audible
warning
buzzer
(10)
Reverse
the
removing procedure
in (5)
to
(8).
Section Na.5
SWITCHES,
WARNING LAMPS AND
CONTROLS
(GHNS and GHDS
cars
from Car No.
294251)
NOTE:
Refer
to
Section
Na.1
for
the
removal and
re■tting
of the instruments,
steering-column
switches,
door
courtesy
switch,
audible warning switch and
buzzer.
Removing
IMPORTANT:
Disconnect the
battery before
attempt-
ing
to
remove any
of the
switches, warning lamps
or
controls.
Hazard
warning
switch
(1)
Remove the
centre
console—Section
R.34.
(2) Withdraw
the
bulb
holder
from the
switch retainer.
(3) Disconnect the
wiring
plug
from the
switch.
(4)
Remove
the
retainer
from
the
switch
and
withdraw
the
switch from
the
console.
Lighting switch
.
(5)
Unscrew
the three
screws
securing
the-fascia
L.H.
lower
trim board and
pull
the
board
forward
to;
release it from its
retaining clips
at
the
back
of
the
fascia.
(6)
Remove the
bulb
holder from the
switch
retainer.
(7) Disconnect
the
wiring from the
switch.
(8)
Remove the
retainer
from
the
switch
and
withdraw
the switch from the
fascia.
Na.5