Motion Control Engineering 2000 - Page 289

Index-7
IND. CNCL. CALLS ON STOP? 5-49
Independent Service message 6-21
Independent Service Operation 1-15
Independent Service Operation message 6-21
Independent service, call cancellation 5-49
INDFRC, Independent Service/Fire Service Phase 2 Output
5-45
INDO, Independent Service Output 5-45
Initial Stepping Positions 3-18
INN 6-44
INSDN, Inspection Down Input 5-35
INSP, Inspection output 5-45
Inspection 6-40
INSPECTION DIRECTION SW. FAILURE message 6-22
Inspection Mode Fault Bypass 5-66
Inspection Operation 1-13
INSPECTION OPERATION message 6-22
Inspection Operation message 6-22
INSUP, Inspection Up Input 5-35
INV. DOOR CLOSE LIMIT option 5-26
IP address screen 5-98
IRCOF, Front Infrared Cutout input 5-35
IRCOR, Rear Infrared Cutout input 5-35
iReport 1-20
iReport screen 5-99
ISR, In service and ready flag 5-10
ISRT, In Service and Running Output 5-45
ISRT, In service truly flag 5-10
ISV, In service flag 5-10
ISV, In Service Output 5-45
ISVF, Flasing In-Service output 5-45
IUL, In Use Light Output 5-45
J
Jumper 6-3
Jumpers for Construction operation 3-5
K
KCE ENABLE / DISABLE option 5-52
L
landing system
installation of 3-10
installation of magnets 3-10
Landing System Interface Board 6-69
Landing System Redundancy Failure message 6-22
Landing system troubleshooting 6-8
LCD display 5-7, 5-14, 5-15
LD, Level down input flag 5-10
LEAVE DOORS OPEN ON CTL option 5-24
LEAVE DOORS OPEN ON EPI option 5-25
LEAVE DOORS OPEN ON PTI/ESS option 5-23
Level Dead Zone 5-104
Leveling Down message 6-22
Leveling Input is absent message 6-22
LEVELING SENSOR ENABLED/DISABLED option 5-52
Leveling Sensor Failed - OFF Position message 6-22
Leveling Sensor Failed - ON Position message 6-22
Leveling Sensor Failure message 6-23
Leveling up message 6-23
LFP, Lower parking floor flag 5-10
LIGHT LOAD CAR CALL LIMIT option 5-48
Light Load Weigher Condition message 6-23
LIGHT LOAD WEIGHING? option 5-48
limit switches
installation of 3-10
limit switches, installation of 3-10
LIMITED DOOR RE-OPEN OPTION option 5-24
LLI, Light Load Input 5-35
LLI, Light load input flag 5-10
LLW, Light Load Weigher Output 5-45
LLW, Light load weighing function input flag 5-10
load weighing system
DLW (Dispatch load weigher threshold) 5-63
HLW (Heavy load weigher threshold) 5-63
LLW (Light load weigher threshold) 5-63
OLW (Overloaded car threshold) 5-63
setting load thresholds 5-63
LOBBY DOOR TIMER 5-26
LOBBY FLOOR option 5-19
LOS, Low Oil Switch input 5-35
Loss of door lock out of door zone message 6-23
LOT, Lobby door time flag 5-10
LOTR, Lobby door time (rear) flag 5-10
LOW OIL SWITCH CONTACT (N.O. / N.C.) option 5-53
Low Oil Switch Input is Activated message 6-23
Low voltage signal wiring 2-10
LOW VOLTATGE FIRE SENSORS? option 5-21
LS-EDGE 5-100
LS-EDGE LANDING SYSTEM? 5-55
LS-EDGE-EL Learn 3-20
LS-QUTE Landing System 1-9
assembly drawing 7-15
installation of 3-9, 3-10
wiring diagram 7-15
LSR, Landing System Redundancy Input 5-35
LS-STAN Landing System 1-10
LU, Level up input flag 5-10
LWB, Load Weigher Bypass input 5-35
LWCE, Load weighing change enable flag 5-10
M
M CONTACTOR INSTALLED? option 5-54
M2L INPUT FAILURE message 6-23
MABB INPUT FAILURE message 6-23
MABBR INPUT FAILURE message 6-23
MABGF INPUT FAILURE message 6-24
MABGR INPUT FAILURE message 6-24
MABT INPUT FAILURE message 6-24
MABTR INPUT FAILURE message 6-24
Machine Room Inspection 1-14
MACHINE ROOM INSPECTION message 6-24
MASS 524 CMR FIRE CODE? option 5-21
MASSACHUSETTS EMS SERVICE? option 5-50
MASTER SOFTWARE KEY option 5-50
MBAB INPUT FAILURE message 6-24
MC-CPI board 6-60, 6-64
MC-CPI CAN data viewing 5-97
MC-LSI 6-69