QuickLabel QL-60

To Next Page

To Previous Page

Touchscreen Display

QL-30/60 User Guide 31

Test

Security

Diagnostics

Extras

Help

Service

Table 6: Structure of the menu (Continued)

1st Selection Level 2nd Selection Level 3rd Selection Level

Main Page

Default Chapter5
- Contact Information5
- Declaration of Conformity7
- Table of Contents9
Part 1: Operation15
Chapter 1: Introduction17
- Instructions17
- Intended Use17
Introduction17
- Safety Instructions17
- Environment18
Chapter 2: Installation19
- Print Unit20
- Connections21
- Device Overview19
  - Overview19
Installation19
- Installing the WLAN Stick22
- Unpacking and Setting-Up the Printer22
- Connecting the Device23
  - Connecting to the Power Supply23
  - Connecting to a Computer or Computer Network23
- Switching on the Device23
Chapter 3: Touchscreen Display25
- Start Screen25
Touchscreen Display25
- Structure of the Menu29
- Navigation in the Menu32
- Service Key35
Chapter 4: Loading Media37
- Inserting the Media Strip into the Printhead38
- Setting the Label Sensor39
- Winding up the Media Strip in Rewind Mode40
- Removing the Wound Roll41
- Winding up the Liner in Peel-Off Mode42
Loading Media37
- Loading Roll Media37
  - Positioning the Media Roll on the Roll Retainer37
- Loading Fanfold Media43
- Setting the Head Locking System44
  - Ql-30, Ql-60, Ql-30P, Ql-60P44
  - Ql-30M, Ql-60M, Ql-30Mp, Ql-60Mp45
- Removing and Installing the Rewind Guide Plate, Dispense Plate or Tear-Off Plate46
  - Removing a Plate46
  - Installing a Plate46
- Loading Transfer Ribbon47
- Setting the Feed Path of the Transfer Ribbon48
Chapter 5: Printing Operation49
Printing Operation49
- Synchronization of the Media Feed49
- Tear-Off Mode49
- Internal Rewinding50
- Peel-Off Mode50
Chapter 6: Cleaning51
Cleaning51
- Cleaning Information51
- Cleaning the Print Roller51
- Cleaning the Printhead51
- Cleaning the Label Sensor52
Chapter 7: Fault Correction53
- Error Display53
Fault Correction53
- Error Messages and Fault Correction54
- Problem Solution57
Chapter 8: Media59
Media59
- Media Dimensions59
- Device Dimensions61
- Reflective Mark Dimensions63
- Cut-Out Mark Dimensions64
Part 2: Configuration67
Connecting Label Printer to Computer69
- Adjusting Windows Printer Setting70
Chapter 9: Connecting Label Printer to Computer70
- Connecting Label Printer Via Ethernet Interface70
- Print Services Raw-IP and LPR/LPD in MS Windows70
- Connecting Label Printer Via USB Interface71
- Setting up a WLAN Connection71
- Connecting Label Printer Via RS-232 Interface72
- Setting up a Bluetooth Connection73
Chapter 10: Info75
Chapter 11 Security77
Chapter 12: Configuration79
- Labels82
- Ribbon83
- Tearing-Off83
- Cutting84
- Peeling-Off85
- Labeling85
- Interfaces87
- Errors91
- Region92
- Time93
- Display94
- Interpreter94
- Zpl95
Configuration79
- Configuration Via Control Panel79
  - Printing79
- Configuration Via the Web Interface95
Chapter 13: Test Functions103
- Overview103
- Status Print103
Test Functions103
- Font List104
- Device List105
- Test Grid107
- Wifi Status108
- ASCII Dump Mode111
Chapter 14: Diagnostic Functions111
- Example112
Diagnostic Functions111
- Label Profile112
- Event Log114
- Save Data Stream115
- Save Print Image116
- Save System Log117
Chapter 15: Extras119
Extras119
- Firmware Update119
- Save Settings119
- Load Settings120
- Reset Settings120
- Cleaning Interval121
- Reset Passwords121
- Legal Notices122
Chapter 16: Help123
- Calibrate Label Sensor125
Chapter 17: Service Functions125
- Reset Service Counter125
Service Functions125
- Length Correction126
- Printer Model126
Chapter 18: I/O Interface127
I/O Interface127
- Pin Assignment127
- Circuit Diagram of Inputs and Outputs130
- Solution Examples131
Chapter 19: FTP Printer Management143
- FTP Login143
FTP Printer Management143
- FTP Printing143
- FTP Access to Storage Devices144
- FTP Firmware Update144
Chapter 20: Storage Devices145
- Directory Structure145
- Installation145
Storage Devices145
- Suitable Storage Devices145
- Storage Device Functions146
- Writing146
  - Example146
Chapter 21: Remote Access Via VNC149
- Establishing a Connection149
- Preparing the Computer149
- Preparing the Printer149
Remote Access Via VNC149
Chapter 22: External Keyboard151
- Connecting External Keyboard151
External Keyboard151
- Keyboard Assignment151
- Special Key Functions152
  - General152
  - In the Menu and for Entry of Variable Data153
Chapter 23: Firmware Updater155
- Index157

QuickLabel QL-60 - Page 31

Table of Contents

Related product manuals