Siemens HydroRanger 200 HMI - Page 9

Table of contents
HydroRanger 200 HMI
Operating Instructions, 06/2018, A5E36281317-AC
7
8.6.1.1 Units (2.1.1.) ......................................................................................................................... 162
8.6.1.2 Level selector (2.1.2.) ........................................................................................................... 162
8.6.1.3 Sensor mode (2.1.3.) ............................................................................................................ 163
8.6.1.4 Transducer selector (2.1.4.) .................................................................................................. 164
8.6.1.5 Transducer (2.1.5.) ............................................................................................................... 164
8.6.1.6 Material (2.1.6.) ..................................................................................................................... 165
8.6.1.7 Short shot frequency (2.1.7.) ................................................................................................ 165
8.6.1.8 Long shot frequency (2.1.8.) ................................................................................................. 165
8.6.1.9 Short shot duration (2.1.9.) ................................................................................................... 166
8.6.1.10 Long shot duration (2.1.10.) .................................................................................................. 166
8.6.1.11 Number of short shots (2.1.11.) ............................................................................................ 166
8.6.1.12 Number of long shots (2.1.12.) ............................................................................................. 167
8.6.1.13 Shot synchro (2.1.13.) .......................................................................................................... 167
8.6.1.14 Scan delay (2.1.14.) .............................................................................................................. 167
8.6.1.15 Scan time (2.1.15.) ................................................................................................................ 168
8.6.1.16 Shot delay (2.1.16.) ............................................................................................................... 168
8.6.1.17 Shot/pulse mode (2.1.17.) .................................................................................................... 168
8.6.2 Calibration (2.2.) ................................................................................................................... 169
8.6.2.1 Level selector (2.2.1) ............................................................................................................ 169
8.6.2.2 Span (2.2.2.) ......................................................................................................................... 169
8.6.2.3 Transducer selector (2.2.3.) .................................................................................................. 169
8.6.2.4 Empty (2.2.4.) ....................................................................................................................... 170
8.6.2.5 Sensor offset (2.2.5.) ............................................................................................................
171
8.
6.2.6 Blanking (2.2.6.) .................................................................................................................... 171
8.6.2.7 Range extension (2.2.7.) ...................................................................................................... 172
8.6.3 Rate (2.3.) ............................................................................................................................. 172
8.6.3.1 Transducer selector (2.3.1.) .................................................................................................. 172
8.6.3.2 Fill rate/minute (2.3.2.) .......................................................................................................... 173
8.6.3.3 Empty rate/minute (2.3.3.) .................................................................................................... 173
8.6.3.4 Response rate (2.3.4.) .......................................................................................................... 174
8.6.3.5 Rate filter (2.3.5.) .................................................................................................................. 175
8.6.3.6 Rate filter time (2.3.6.) .......................................................................................................... 175
8.6.3.7 Rate filter distance (2.3.7.) .................................................................................................... 175
8.6.3.8 Level selector (2.2.8) ............................................................................................................ 176
8.6.3.9 Filling indicator (2.3.9.).......................................................................................................... 176
8.6.3.10 Emptying indicator (2.3.10.) .................................................................................................. 176
8.6.4 Fail-safe (2.4.) ....................................................................................................................... 177
8.6.4.1 Transducer selector (2.4.1.) .................................................................................................. 177
8.6.4.2 LOE timer (2.4.2.) ................................................................................................................. 177
8.6.4.3 Level selector (2.4.3.) ........................................................................................................... 178
8.6.4.4 Fail-safe mode (2.4.4.) .......................................................................................................... 178
8.6.4.5 Material level (2.4.5.) ............................................................................................................ 178
8.6.4.6 Fail-safe advance (2.4.6.) ..................................................................................................... 179
8.6.4.7 mA Output selector (2.4.7.) ................................................................................................... 179
8.6.4.8 mA Fail-safe mode (2.4.8.) ...................................................................................................
179
8.
6.4.9 mA Fail-safe value (2.4.9.) ....................................................................................................
180
8.
6.5 Current Output (2.5.) ............................................................................................................. 180
8.6.5.1 mA output selector (2.5.1.) ................................................................................................... 180
8.6.5.2 mA output range (2.5.2.) ....................................................................................................... 180
8.6.5.3 Current output function (2.5.3.) ............................................................................................. 181
8.6.5.4 mA output allocation (2.5.4.) ................................................................................................. 181
8.6.5.5 4 mA setpoint (2.5.5.)............................................................................................................ 182