Siemens SITRANS TSinsert - Page 5

7.3 Locking the device ............................................................................................................. 65
7.3.1 Introduction....................................................................................................................... 65
7.3.2 Enable write protection with write protection switch .......................................................... 65
7.3.3 Enable the User PIN on the display ..................................................................................... 66
7.3.4 Enable the button lock on the display................................................................................. 67
8 Parameter assignment......................................................................................................................... 69
8.1 Overview of parameters and functions ............................................................................... 69
8.1.1 Parameters and functions................................................................................................... 69
8.1.2 Advanced functions ........................................................................................................... 72
8.2 Parameter assignment with USB modem and SIPROM T ...................................................... 73
8.3 Parameter assignment over device with display .................................................................. 74
8.3.1 Input type 1 [01]................................................................................................................ 74
8.3.2 Connection type for input 1 [02] ........................................................................................ 78
8.3.3 Wire resistance for connecting cable at Input 1 [03] ........................................................... 78
8.3.4 Input type 2 [04]................................................................................................................ 78
8.3.5 Connection type for input 2 [05] ........................................................................................ 81
8.3.6 Wire resistance for connecting cable at Input 2 [06] ........................................................... 82
8.3.7 Assignment of the primary variable [07]............................................................................. 82
8.3.7.1 Introduction....................................................................................................................... 82
8.3.7.2 Setting the assignment of the primary variable................................................................... 83
8.3.8 Unit [08]............................................................................................................................ 83
8.3.9 Lower range value [09]/Upper range value [10].................................................................. 84
8.3.9.1 Lower range value [09] parameter ..................................................................................... 84
8.3.9.2 Upper range value [10] parameter ..................................................................................... 84
8.3.9.3 Adjusting lower range value/upper range value .................................................................. 84
8.3.10 Damping value [11] ........................................................................................................... 85
8.3.10.1 Damping value parameter.................................................................................................. 85
8.3.10.2 Set damping value ............................................................................................................. 85
8.3.11 Functional Safety [12]........................................................................................................ 86
8.3.12 Loop test [13].................................................................................................................... 86
8.3.12.1 Loop test with preset loop current value............................................................................. 86
8.3.12.2 Loop test with user de󹪝ned loop current value.................................................................... 87
8.3.13 One-point calibration input 1 [14]...................................................................................... 88
8.3.14 One-point calibration input 2 [15]...................................................................................... 88
8.3.15 Change User PIN [16]......................................................................................................... 88
8.3.15.1 Change user PIN ................................................................................................................ 88
8.3.16 PIN recovery [17] ............................................................................................................... 89
8.3.16.1 Recovering the user PIN ..................................................................................................... 90
8.3.17 User PIN [18] ..................................................................................................................... 91
8.3.17.1 User PIN............................................................................................................................. 91
8.3.17.2 Enable user PIN.................................................................................................................. 91
8.3.17.3 Disable user PIN ................................................................................................................. 91
8.3.18 Minimum measured peak value at Input 1 [19]................................................................... 92
8.3.19 Maximum measured peak value at Input 1 [20].................................................................. 92
8.3.20 Minimum measured peak value at Input 2 [21]................................................................... 93
8.3.21 Maximum measured peak value at Input 2 [22].................................................................. 93
8.3.22 Minimum transmitter electronics temperature [23] ............................................................ 93
8.3.23 Maximum transmitter electronics temperature [24]............................................................ 93
8.3.24 Button lock [25]................................................................................................................. 93
8.3.24.1 Enabling button lock.......................................................................................................... 94
Table of contents
SITRANS TS100/TS200/TS300/TS500/TSinsert/TSthermowell
Operating Instructions, 08/2020, A5E47810090-AA 5