Sonifex S2 - Page 133

To Next Page

To Previous Page

S2 User Handbook

121

S2ODAF/S2ODA DIGITAL OUTPUT AUD CHANNEL

WITH & WITHOUT MASTER FADER VERSION 2

S2ODAF/S2ODA DIGITAL OUTPUT

AUD CHANNEL WITH & WITHOUT

MASTER FADER VERSION 2

Mode 3 : Always o. AUD can never be selected as the meter feed.

CR MON

Mode 1 : Normal. The Control Room Monitor channel be selected as the meter feed as

normal.

Mode 2 : Always on. The Control Room Monitor channel is permanently selected as the

meter feed.

Mode 3 : Always o. The Control Room Monitor channel can never be selected as the

meter feed.

Note: If more than one button is set to mode 2 (Always on) then the meter feed will be

a mix of these sources. This may not be desirable in most applications.

Main Page

Default Chapter3
- Table of Contents3
- Warranty and Liability7
- Returning the Warranty Card9
- Unpacking the S29
- Safety of Mains Operated Equipment10
- Fuse Rating10
- Power Cable and Connection10
- WEEE & Rohs Directives - Sonifex Statement11
- Reporting Faults12
1 Introduction13
- Innovative Design13
- Fig 1-1 : S2-15 Chassis Complete with13
- Fig 1-2 : S2-7SS Script Space14
- Superb Audio Quality and Unquestionable Reliability15
- Features15
2 Installation Notes16
- Atmosphere16
- Electromagnetic Radiation16
- Dimensions and Cut-Out Sizes16
- Fig 2-1 : Mixer Profile16
- Channel Configuration17
- Connectors and Cabling17
  - Channels17
- Fig 2-2 : Mixer Cut-Out Details17
- Fig 2-3 : XLR Connectors18
- Fig 2-4 : RCA Phono Connector18
- Fig 2-5 : BNC Connector18
- Fig 2-6 : 1/4" Jack Connectors19
- Fig 2-7 : 9 Pin & 15 Pin D-Type Connectors19
- Fig 2-8 : 25 Pin D-Type Connectors20
- Fig 2-9 : 9 Pin D-Type Power Connectors20
- System Block Diagrams21
- Applications23
- Fig 2-12 : Using the Sonifex RB-LC3 to Control an On-Air Light23
- Removing & Replacing Channels25
- Connecting a Split Desk26
- Fig 2-13 : Mixer Bus Cable Slots26
- Fig 2-14 : Mixer Bus Cable Screen26
- Fig 2-15 : Cable & Channel Connection27
- Fig 2-16 : Meterbridge Interconnection27
3 Power Supply28
- S2-PSU Power Supply (Old Version)28
- Front Panel28
- Fig 3-1 : S2-PSU Front Panel28
- Fig 3-2 : S2-PSU Rear Panel28
- Rear Panel29
- Safety of Mains Operated Equipment29
- Ordering the Correct Mains Lead30
- Power Cable and Connection30
- Fuse Rating30
- S2-PSU Power Supply (New Version)31
- Fig 3-3 : New S2-PSU Front Panel31
- Fig 3-4 : New S2-PSU Rear Panel32
- Front Panel Indicators33
- Fig 3-5 : S2-PSUS Front Panel33
- Rear Panel34
- Fig 3-6: S2-PSUS Rear Panel34
- Fig 3-7: New S2-PSU Diagram36
4 Input Channels37
- S2-CML MIC/Line Input Channel37
- S2-CMM MIC/MIC Input Channel37
- S2-CS Dual Stereo Line Input Channel37
- S2-CSE Dual Stereo Line Input with EQ Channel38
- S2-CSG Stereo Line with Gram Input Channel38
- S2-CDS Digital Dual Stereo Input Channel38
- S2-CDSE Digital Dual Stereo Input with EQ Channel38
- S2-C6SS 6 Way Stereo Line Source Select Channel38
- S2-CT Telco Input Channel38
- S2-CSMM Stereo MIX-Minus Channel39
- S2-PG S2 Penny & Giles Conductive Plastic Fader39
5 S2-CML MIC/Line Channel with EQ40
- Panel Controls40
- Rear Panel41
- Channel Options, Jumper Settings and Presets42
- Fig 5-1 : S2 MIC/Line Input Board Layout44
6 S2-CMM MIC/MIC Channel with EQ48
- Panel Controls48
- Rear Panel49
- Channel Options, Jumper Settings and Presets50
  - Fig 6-1 : S2 MIC/MIC Input Board Layout52
7 S2-CSE/S2-CS Dual Stereo Line Channel with & Without EQ55
- Panel Controls55
- Rear Panel56
- Channel Options, Jumper Settings and Presets57
- Fig 7-1 : S2 Dual Stereo Input with58
8 S2-CSGE/S2-CSG Stereo Line and Gram Channel with & Without EQ64
- Panel Controls64
- Rear Panel65
- Channel Options, Jumper Settings and Presets66
- Fig 8-1 : S2 Stereo Line & Gram with67
9 S2 -CDSE/S2-CDS Digital Dual Stereo Line Channel with & Without EQ73
- Panel Controls73
- Rear Panel74
- Channel Options, Jumper Settings and Presets75
- Fig 9-1 : S2 Digital Dual Stereo Input Board Layout76
10 S2-C6SS 6 Way Stereo Line Source Select Channel with EQ82
- Panel Controls82
- Channel Options, Jumper Settings and Presets84
- Fig 10-1 : S2 6 Way Source Selector85
11 S2-CT Telco Channel with EQ88
- Panel Controls88
- Rear Panel89
- Channel Options, Jumper Settings and Presets90
- Fig 11-1 : S2 Telco Input Board Layout91
12 S2 CSMM Stereo MIX Minus Channel with EQ95
- Panel Controls95
- Rear Panel96
- Channel Options, Jumper Settings and Presets97
- Fig 12-1 : S2 Stereo MIX-Minus Board98
13 Output Channels104
- S2-ODP Digital PGM Output Channel &S2-ODPF Digital PGM Output Channel with Master Fader104
- S2-ODA Digital AUD Output Channel & S2-ODAF Digital AUD Output Channel with Master Fader104
- S2-OMC Control Room Monitor Channel104
- S2-OMS Studio Monitor Channel105
14 S2-ODPF/S2-ODP Digital Output PGM Channel with & Without Master Fader (Version 1)106
- Panel Controls106
- Rear Panel107
- Channel Options, Jumper Settings and Presets108
- Fig 14-1 : S2 Digital PGM Output Board109
- Fig 14-2 : S2 Digital PGM Output with Fader Board Layout110
15 S2-ODPF/S2-ODP Digital Output PGM Channel with & Without Master Fader (Version 2)113
- Panel Controls113
- Rear Panel114
- Channel Options, Jumper Settings and Presets115
- Fig 15-1 : S2 Digital PGM Output Board Layout117
- Fig 15-2 : S2 Digital PGM Output with Fader Board Layout117
16 S2-ODAF/S2-ODA Digital Output AUD Channel with & Without Master Fader (Version 1)120
- Panel Controls120
- Rear Panel121
- Channel Options, Jumper Settings and Presets122
- Fig 16-1 : S2 Digital AUD Output Board123
- Fig 16-2 : S2 Digital AUD Output with Fader Board Layout124
17 S2-ODAF/S2-ODA Digital Output AUD Channel with & Without Master Fader (Version 2)127
- Panel Controls127
- Rear Panel127
- Channel Options, Jumper Settings and Presets129
- Fig 17-1 : S2 Digital AUD Output Board Layout130
- Fig 17-2 : S2 Digital AUD Output with Fader Board Layout130
18 S2-OMC Control Room Monitor Channel134
- Panel Controls134
- Rear Panel135
- Channel Options and Jumper Settings136
- Fig 18-1 : Control Room Monitor Board136
19 S2-OMS Studio Monitor Channel140
- Panel Controls140
- Rear Panel141
- Channel Options and Jumper Settings142
- Fig 19-1 : Studio Monitor Board Layout142
20 Meterbridge Modules146
- Meterbridge Module Types146
- Meterbridge Distribution Board147
- Fig 20-1 : Meterbridge Distribution Board Layout147
- S2-MB1-5 Meterbridge Blanking Plates148
- S2-ML Meterbridge Loudspeaker Monitor Panel148
- Fig 20-2 : Blanking Plate148
- Fig 20-3 : Loudspeaker Monitor Panel148
- S2-ML53 LED Meter Panel149
- Fig 20-4 : PPM & True PPM Meter Panel149
- Fig 20-5 : VU Meter Panel149
- Fig 20-6 : VU & PPM LED Meter Panel150
- S2-MPH Meterbridge Phase Meter Panel151
- Fig 20-7 : Phase Meter Panel151
- S2-MTB6 Meterbridge 6 Way Talkback Panel152
- S2-MTBS Meterbridge Station Master Talkback Panel153
- Fig 20-10A : S2-M6SS Panel155
- Fig 20-10B : S2-M6SS Diagram156
  - Switch Panel with 1157
  - Switch Panel with 3157
- S2-MSB1 Meterbridge Switch Panel with 1 Button157
- S2-MSB3 Meterbridge Switch Panel with 3 Buttons157
  - Connection157
- Panel157
- S2-MT Meterbridge Timer Panel158
- Overview158
- Panel Controls158
- Fig 20-13 : Meterbridge Timer Panel158
- Rear Panel159
- Configuring the Timer159
21 Technical Specifications164
- S2 Mixer Weights and Boxed Dimensions166
- Glossary167

Sonifex S2 - Page 133

Table of Contents