Toshiba E-Studio 5540c - Page 20

e-STUDIO5540C/6540C/6550C/5560C/6560C/6570C © 2011 - 2015 TOSHIBA TEC CORPORATION All rights reserved
CONTENTS
4
4.5.21 Drawer transport sensor (S77/S85/S93/S101) ................................................ 4-60
4.5.22 Drawer empty sensor (S75/S83/S91/S99)....................................................... 4-61
4.5.23 Drawer tray-up sensor (S76/S84/S92/S100) ................................................... 4-61
4.5.24 Drawer bottom sensor (S74/S82/S90/S98) ..................................................... 4-62
4.5.25 Registration roller (Rubber) ............................................................................. 4-62
4.5.26 Paper dust cleaning brush (registration roller)................................................. 4-63
4.5.27 Registration guide............................................................................................ 4-63
4.5.28 Registration sensor (S52) ................................................................................ 4-64
4.5.29 Registration roller (Metal) ................................................................................ 4-65
4.5.30 2nd transfer side paper clinging detection sensor (S51) ................................. 4-65
4.5.31 Media sensor (S69) ......................................................................................... 4-66
4.5.32 Feed cover sensor (S114) ............................................................................... 4-68
4.5.33 Drawer ............................................................................................................. 4-68
4.5.34 Drawer paper size detection sensor-1/2 (S79/S80/S87/S88/S95/S96/S103/S104)
......................................................................................................................... 4-69
4.5.35 Registration motor (M39) ................................................................................. 4-69
4.5.36 Feed/transport drive unit.................................................................................. 4-70
4.5.37 Transport motor-1 (M40).................................................................................. 4-70
4.5.38 Transport motor-2 (M41).................................................................................. 4-71
4.5.39 Feed motor (M42) ............................................................................................ 4-71
4.5.40 Feed/transport motor (M43)............................................................................. 4-71
4.5.41 Paper feed drive unit........................................................................................ 4-72
4.5.42 3rd drawer transport clutch (CLT4)/3rd drawer feed clutch (CLT5)
(e-STUDIO5540C/6540C/6550C).................................................................... 4-72
4.5.43 3rd drawer transport clutch (CLT4)/3rd drawer feed clutch (CLT5)
(e-STUDIO5560C/6560C/6570C).................................................................... 4-73
4.5.44 4th drawer transport clutch (CLT6)/4th drawer feed clutch (CLT7)
(e-STUDIO5540C/6540C/6550C).................................................................... 4-74
4.5.45 4th drawer transport clutch (CLT6)/4th drawer feed clutch (CLT7)
(e-STUDIO5560C/6560C/6570C).................................................................... 4-74
4.5.46 Tray-up motor-1 (M44)..................................................................................... 4-75
4.5.47 Tray-up motor-2 (M45)..................................................................................... 4-77
4.5.48 Transfer belt paper clinging detection sensor (S47) ........................................ 4-78
4.5.49 Tandem LCF tray-up motor (M46) ................................................................... 4-79
4.5.50 Tandem LCF end fence motor (M47) .............................................................. 4-80
4.5.51 Tandem LCF standby unit ............................................................................... 4-81
4.5.52 Tandem LCF feeding unit ................................................................................ 4-82
4.5.53 Stopper opening/closing solenoid (front) (SOL10)/Stopper opening/closing
detection sensor (front) (S110) ........................................................................ 4-82
4.5.54 Stopper opening/closing solenoid (rear)/Stopper opening/closing detection sensor
(rear) (S111) .................................................................................................... 4-84
4.5.55 Tandem LCF bottom sensor (S107) ................................................................ 4-85
4.5.56 Standby side tray paper amount detection sensor (S106)............................... 4-85
4.5.57 End fence home position sensor (S112).......................................................... 4-87
4.5.58 End fence stop position sensor (S113)............................................................ 4-88
4.5.59 Standby side empty sensor (S109).................................................................. 4-89
4.5.60 Standby side tray detection sensor (S108)...................................................... 4-89
4.5.61 Tandem LCF solenoid (SOL9)......................................................................... 4-90
4.6 Process Unit Related Section ......................................................................................... 4-91
4.6.1 Pulling out the process unit (EPU tray)............................................................ 4-91
4.6.2 Drum cleaner unit ............................................................................................ 4-95
4.6.3 Drum ............................................................................................................... 4-97
4.6.4 Drum cleaning blade ....................................................................................... 4-97
4.6.5 Blade side seal ............................................................................................... 4-98
4.6.6 Main charger unit ............................................................................................. 4-99
4.6.7 Main charger grid ............................................................................................ 4-99
4.6.8 Needle electrode cleaner ................................................................................ 4-99
4.6.9 Needle electrode ........................................................................................... 4-100