Valtra 6550 - Page 503

124
Model Code Page
37. Autocontrol 5
1. 8. 2000
370 9A
6250--8950
1. 9. 2002
I.D. numbers of programs used in Pro -
duction, in Spare Parts and in Service
(AC 5 only):
Note! Sorted according to the main program version.
Beside the I.D. numbers there is information, with which
can be concluded whether the tractor has a correct pro-
gram.
Tractor chassis numbers in brackets show how old tractor
the program is and which program can be fitted. I.D.
numberscanbeseeninthetractordisplay.InthePCmoni-
tor the numbers change places, e.g. 5162 --- > 6251.
IMPORTANT! Only the newest programs can be used in
Service and Spare Parts (v ersions 53 and 65).
Note! If an I.D number of a tractor cannot be found in this
list, ask Tractor Service.
Main program no. 38 (these must not be on field).
Thesemustbereplacedwithprogramversion
53.
These must not be used in Service.
10 38
1)
PTO 1000
17 38
1)
PTO 1000/540E
51 38
1)
PTO 540/1000
57 38
1)
PTO 540/540E
71 38
1)
PTO 540E/1000E (8350Hi)
Main program no. 40 (these must not be on field).
Thesemustbereplacedwithprogramversion53
.
ThesemustnomorebeusedinService.
10 40
1)
PTO 1000
17 40
1)
PTO 1000/540E
51 40
1)
PTO 540/1000
57 40
1)
PTO 540/540E
71 40
1)
PTO 540E/1000E (8350Hi)
Main program no. 41 (H49112---J38342).
These can be replaced with program version 53
.
ThesemustnomorebeusedinService.
10 41 PTO 1000
17 41 PTO 1000/540E
51 41 PTO 540/1000
57 41 PTO 540/540E
71 41 PTO 540E/1000E (8350Hi)
Main program no. 42 (J38343---J47541).
These can be replaced with program version 65
.
ThesemustnomorebeusedinService.
10 42
2)
PTO 1000
17 42
2)
PTO 1000/540E
51 42
2)
PTO 540/1000
57 42
2)
PTO 540/540E
71 42
2)
PTO 540E/1000E (8350Hi)
NumbersusedonlybyServiceandSpareP
arts:
21 42
2)
6250Hi ---8950Hi (Ei 8350Hi)
31 42
2)
8350Hi
Main program no. 43 (J38343---J47541).
These can be replaced with program version 65
.
Thes must no more be used in Service.
10 43
2)
PTO 1000
17 43
2)
PTO 1000/540E
51 43
2)
PTO 540/1000
57 43
2)
PTO 540/540E
71 43
2)
PTO 540E/1000E (8350Hi)
Main program no. 50.
NumbersusedonlybyServiceandSpareParts.
These can be replaced with program version 53
.
ThesemustnomorebeusedinService.
22 50
1)
6250Hi ---8950Hi (Ei 8350Hi)
32 50
1)
8350Hi
Main program no. 52 (---J38342).
NumbersusedonlybyServiceandSpareParts.
Fits to tractors, if the end of the control unit ser. no. is at
least 00400 o r greater.
These can be replaced with program version 53
.
ThesemustnomorebeusedinService
20 52
1)
6250Hi ---8950Hi (Ei 8350Hi)
23 52 6250Hi --- 8950Hi (Ei 8350Hi)
30 52
1)
8350Hi
33 52 8350Hi
Main program no. 53 (H49112---J38342).
NumbersusedonlybyServiceandSpareParts.
Fits to tractors, if the end of the control unit ser. no. is at
least 00400 or greater.
Thesemustbeusedinservice
These programs are in disk 340 422 60.
23 53 6250Hi --- 8950Hi (Ei 8350Hi)
33 53 8350Hi
1) A new program must be input into the co ntrol unit in
connection with service (main program version 53).
2) If a tractor has the reverse drive controls, a new pro-
gram must be input (main program version 65). Af-
fects function of the clutch pedal and AutoDPS when
the seat is turned rearwards.
Note! If in the test mode FII the I.D. number is 9953 or
9965 after programming or after control unit change,
the parameter file has not been input. Input correct
parameter file according to instr. on page 370---24B.
Note! If the clutch pedal has malfunctions or the tractor has
malfunctions (e. g. fault codes P101...P109), the trans-
mission has jammed or if tractors transmission has not dis-
engagedcompletywithclutchpedal,withHiShiftbuttonor
with shuttle lever, then must a new program be input (main
program version 53 or 65 and parameter file). Program-
ming instructions on page 370---24B.